Electrolux EDE 57160W ユーザーズマニュアル
installation
electrolux 25
T
Th
he
e ffe
ee
ett m
mu
us
stt n
ne
ev
ve
err b
be
e rre
em
mo
ov
ve
ed
d..
D
Do
o n
no
ott rre
es
sttrriic
ctt tth
he
e ffllo
oo
orr c
clle
ea
arra
an
nc
ce
e
tth
hrro
ou
ug
gh
h d
de
ee
ep
p p
piille
e c
ca
arrp
pe
etts
s,, s
sttrriip
ps
s o
off
w
wo
oo
od
d o
orr s
siim
miilla
arr.. T
Th
hiis
s m
miig
gh
htt c
ca
au
us
se
e h
he
ea
att
b
bu
uiilld
d--u
up
p w
wh
hiic
ch
h w
wo
ou
ulld
d iin
ntte
errffe
erre
e w
wiitth
h tth
he
e
o
op
pe
erra
attiio
on
n o
off tth
he
e a
ap
pp
plliia
an
nc
ce
e..
IIm
mp
po
orrtta
an
ntt
The hot air emitted by the tumble dryer
can reach temperatures of up to 60°C.
The appliance must therefore not be
installed on floors which are not resistant
to high temperatures.
When operating the tumble dryer, the
room temperature must not be lower
than +5°C and higher than +35°C, as it
may affect the performance of the
appliance.
can reach temperatures of up to 60°C.
The appliance must therefore not be
installed on floors which are not resistant
to high temperatures.
When operating the tumble dryer, the
room temperature must not be lower
than +5°C and higher than +35°C, as it
may affect the performance of the
appliance.
Fitting the vent hose
A special stacking kit is available through
your local Service Force Centre. To
simplify the installation, there is a choice
of vent outlets: one at the back, the
others in the left and right-hand side.
your local Service Force Centre. To
simplify the installation, there is a choice
of vent outlets: one at the back, the
others in the left and right-hand side.
Connect the hose to whichever is the
more convenient by pulling the ring nut
(A) from the vent outlet at the back,
screwing it on to the hose and pushing it
firmly back into place. The unused vents
should now be sealed with the special
snap covers provided.
more convenient by pulling the ring nut
(A) from the vent outlet at the back,
screwing it on to the hose and pushing it
firmly back into place. The unused vents
should now be sealed with the special
snap covers provided.
Advice: If the hose is long and the
P1027
A
A
P1028
room temperature low, the moisture
might condense inside the hose. This
is an unavoidable natural phenomenon.
To prevent this water from Iying in the
hose or flowing back into the tumble
dryer, it is advisable to drill a small hole
(dia. 3 mm) in the lowest point of the
hose and to place a small container
below it.(See picture, point B).
might condense inside the hose. This
is an unavoidable natural phenomenon.
To prevent this water from Iying in the
hose or flowing back into the tumble
dryer, it is advisable to drill a small hole
(dia. 3 mm) in the lowest point of the
hose and to place a small container
below it.(See picture, point B).
Once connected to the dryer, run the
vent hose to the desired outlet point,
ensuring that the run’s overall length is
less than 2 m, and that it contains no
more than two bends. As to the outlet
itself, if you have decided on a fixed
wall/window grille, a good local
builder’s merchant should be able to
supply you with the necessary fittings
and installation advice.
vent hose to the desired outlet point,
ensuring that the run’s overall length is
less than 2 m, and that it contains no
more than two bends. As to the outlet
itself, if you have decided on a fixed
wall/window grille, a good local
builder’s merchant should be able to
supply you with the necessary fittings
and installation advice.
It is important not to connect the
vent hose to, for example, a cooker
hood, or a chimney or flue pipe
designed to carry the exhaust from
a fuel burning appliance.
vent hose to, for example, a cooker
hood, or a chimney or flue pipe
designed to carry the exhaust from
a fuel burning appliance.
P0055
P1056
B
GB
125986421_gb.qxp 2007-09-14 09:11 Page 25