Panasonic VQT2H52 ユーザーズマニュアル
129
VQT2H52
Color or brightness of the
image changes, or you
may see horizontal bars
in the image.
image changes, or you
may see horizontal bars
in the image.
≥ Color or brightness of the image may change, or you may
see horizontal bars in the image when the object is
recorded under fluorescent light, mercury light or sodium
light, etc., but this is not a malfunction. In this case, record
in Auto Mode or set the shutter speed to 1/60 in areas
where the power supply frequency is 60 Hz, or 1/100 in
areas of 50 Hz.
recorded under fluorescent light, mercury light or sodium
light, etc., but this is not a malfunction. In this case, record
in Auto Mode or set the shutter speed to 1/60 in areas
where the power supply frequency is 60 Hz, or 1/100 in
areas of 50 Hz.
Object seems to be
warped.
warped.
≥ Object seems to be warped slightly when the object moves
across the image very fast, but this is because the unit is
using MOS for the image sensor. This is not a malfunction.
using MOS for the image sensor. This is not a malfunction.
White round spots like
soap bubbles appear on
the recorded picture.
soap bubbles appear on
the recorded picture.
≥ If you take a picture with the
flash in a dark place or indoors,
white round spots may appear
on the picture caused by the
flash reflecting of particles of
dust in the air. This is not a
malfunction.
A characteristic of this is that the number of round spots
and their position differ in every picture.
white round spots may appear
on the picture caused by the
flash reflecting of particles of
dust in the air. This is not a
malfunction.
A characteristic of this is that the number of round spots
and their position differ in every picture.
“ERROR OCCURRED.
PLEASE TURN UNIT OFF,
THEN TURN ON AGAIN.”
is displayed.
PLEASE TURN UNIT OFF,
THEN TURN ON AGAIN.”
is displayed.
≥ The unit has automatically detected an error. Restart the
unit by turning the power off and on.
≥ The power will be turned off in about 1 minute if the power
is not turned off and on.
≥ Repair is needed if it is repeatedly displayed even if it is
restarted. Detach the power connected, contact consumer
support. (
support. (
l 145) Do not attempt to repair the unit by
yourself.
VIERA Link does not
work.
work.
[Setting on this unit]
≥ Connect with a HDMI mini cable (optional). (
≥ Connect with a HDMI mini cable (optional). (
l 94)
≥ Press the MENU button, then touch [SETUP]
#
[VIERA Link]
# [ON]. (l 94)
≥ Turn the power to the unit off and then back on again.
[Setting on other devices]
≥ Depending on HDMI terminal of the TV, the input channel
≥ Depending on HDMI terminal of the TV, the input channel
may not switch automatically. In this case, use the remote
control for the TV to switch input. (For details on how to
switch input, please read the operating instructions for the
TV.)
control for the TV to switch input. (For details on how to
switch input, please read the operating instructions for the
TV.)
≥ Check the VIERA Link setting on the connected device.
≥ Set the setting to control the VIERA Link of the TV to [Off]
≥ Set the setting to control the VIERA Link of the TV to [Off]
once, and the back to [On] again. (Refer to the operating
instructions of the TV for details.)
instructions of the TV for details.)
Problem
Check points
HDCSD10_TM10_TM15P-VQT2H52_eng.book 129 ページ ２００９年７月６日 月曜日 午後１時４６分