Crimestopper Security Products CS-2002DC ユーザーズマニュアル
OPERATING INSTRUCTIONS
TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL)
To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least
1½ seconds. If the system is armed, pressing Button #3 may or may not trip the alarm system when opening
the trunk depending on programming option (10). See page 10.
To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least
1½ seconds. If the system is armed, pressing Button #3 may or may not trip the alarm system when opening
the trunk depending on programming option (10). See page 10.
REMOTE PANIC PROTECTION
To sound the alarm upon command (panic), press and hold the Button #4 (Panic) for at least 2 seconds until
the siren sounds. Press Button #2 (Unlock) to reset panic mode.
To sound the alarm upon command (panic), press and hold the Button #4 (Panic) for at least 2 seconds until
the siren sounds. Press Button #2 (Unlock) to reset panic mode.
PRE-WARNING SHOCK PROTECTION & SENSOR ADJUSTMENT
If a low-level shock to the vehicle is detected, pre-warning protection will activate sounding 6 quick siren chirps
and 1 light flash. If a hard impact is detected the shock sensor should trip the alarm system. Once it is
mounted, adjust the sensor as needed by turning the adjustment screws clockwise to increase or counter-
clockwise to decrease the sensitivity. The sensor is also equipped with 2 small indicator lights to ease the
adjustment process. Green light = Pre-warning disturbance (6 siren chirps). Red light = A full alarm trip.
If a low-level shock to the vehicle is detected, pre-warning protection will activate sounding 6 quick siren chirps
and 1 light flash. If a hard impact is detected the shock sensor should trip the alarm system. Once it is
mounted, adjust the sensor as needed by turning the adjustment screws clockwise to increase or counter-
clockwise to decrease the sensitivity. The sensor is also equipped with 2 small indicator lights to ease the
adjustment process. Green light = Pre-warning disturbance (6 siren chirps). Red light = A full alarm trip.
SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL
This system can be armed and disarmed without siren chirps on an “as needed” basis. Press the Bank #2 on
the side of the remote and within 3 seconds use the lock/unlock buttons to arm/disarm without siren chirps.
This system can be armed and disarmed without siren chirps on an “as needed” basis. Press the Bank #2 on
the side of the remote and within 3 seconds use the lock/unlock buttons to arm/disarm without siren chirps.
PROGRAMMABLE SILENT ARM/DISARM MODE (CHIRP DEFEAT)
The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See
alarm programming option (#8) to enable or disable this feature. See page 10.
The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See
alarm programming option (#8) to enable or disable this feature. See page 10.
EMERGENCY OVERRIDE / DISARM
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to
open the door with the key, which will activate the alarm. Turn the ignition on and press the override/program
button for about 3 seconds (until siren stops). The Alarm will disarm. If you continue to hold the button for
additional 3 seconds, the system will enter the Valet mode.
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to
open the door with the key, which will activate the alarm. Turn the ignition on and press the override/program
button for about 3 seconds (until siren stops). The Alarm will disarm. If you continue to hold the button for
additional 3 seconds, the system will enter the Valet mode.
EMERGENCY DISARM WITH CUSTOM OVERRIDE
If you have programmed your system for Custom Override, follow the same steps above (Emergency
Override) while pressing the valet button 2-15 times as you have programmed. You must continue to hold the
button down on the last press for 5 seconds. The Alarm will disarm and enter the Valet mode, which allows
you to use the vehicle until you can repair/replace the remote transmitter or have the alarm system checked.
If you have programmed your system for Custom Override, follow the same steps above (Emergency
Override) while pressing the valet button 2-15 times as you have programmed. You must continue to hold the
button down on the last press for 5 seconds. The Alarm will disarm and enter the Valet mode, which allows
you to use the vehicle until you can repair/replace the remote transmitter or have the alarm system checked.
15