Crimestopper Security Products CS-2004DC ユーザーズマニュアル
OPTION PROGRAMMING
11. DOUBLE UNLOCK PULSE
This option controls whether the unit will send one or two unlock pulses when disarmed. This feature may be
required for interfacing to existing Factory Keyless Entry or Alarm systems in a vehicle. These systems are found
on some Nissan, VW, Toyota, and Lexus vehicles.
This option controls whether the unit will send one or two unlock pulses when disarmed. This feature may be
required for interfacing to existing Factory Keyless Entry or Alarm systems in a vehicle. These systems are found
on some Nissan, VW, Toyota, and Lexus vehicles.
12. ENABLE/DISABLE CARJACK FEATURES
This option controls the unit’s Car Jack features. Enable or Disable Carjack (Turn ON or OFF) with this option.
This option controls the unit’s Car Jack features. Enable or Disable Carjack (Turn ON or OFF) with this option.
13. STARTER DISABLE CONFIGURATION: NORMALLY CLOSED OR NORMALLY OPEN
This option controls the unit’s on-board Starter disable relay for either “Normally Open” or “Normally Closed”
operation. See page 8 for more information.
This option controls the unit’s on-board Starter disable relay for either “Normally Open” or “Normally Closed”
operation. See page 8 for more information.
PROGRAMMABLE OPTION RESET:
This system provides a “reset method” to restore all options to FACTORY DEFAULT VALUES as listed in the
“Button #2” column of the programmable option chart on page 10. This can be helpful if you have lost track of the
option settings on your system or when you are moving systems from car to car.
This system provides a “reset method” to restore all options to FACTORY DEFAULT VALUES as listed in the
“Button #2” column of the programmable option chart on page 10. This can be helpful if you have lost track of the
option settings on your system or when you are moving systems from car to car.
1. Turn Key to the ON position, wait 5 seconds.
2. Press program / valet button 5 times, after a few seconds the unit will flash the lights 5 times.
3. Push the valet/program button 14 times. Press button carefully. You must get a light flash each time you press
2. Press program / valet button 5 times, after a few seconds the unit will flash the lights 5 times.
3. Push the valet/program button 14 times. Press button carefully. You must get a light flash each time you press
the button. If the unit didn’t flash the lights, then it did not register your press.
4. Press button #2 (Unlock) to reset the options. Lights will flash twice.
5. Turn Ignition OFF. All features should be set at *DEFAULT values.
5. Turn Ignition OFF. All features should be set at *DEFAULT values.
CS-2004TW1 / CS-2004DC TRANSMITTER PROGRAMMING
TRANSMITTER PROGRAMMING NOTES (Read first!):
(1) The CS-2004TW1 will learn up to 4 remotes, any combination of special CS-398 1-way or CS-389LED 2-way
pager remotes.
(2) The CS-2004 will up to 4 one-way remotes. The remote controls for the CS-2004DC & CS-2004TW1 systems
ARE NOT interchangeable.
Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding
remotes, ALL your system’s remote codes must be learned at time of programming! These systems allow storage
of up to 4 different remote codes in memory. Note the slightly difference in program step #4 for either a2004DC or a
2004TW1 system on the next page.
(1) The CS-2004TW1 will learn up to 4 remotes, any combination of special CS-398 1-way or CS-389LED 2-way
pager remotes.
(2) The CS-2004 will up to 4 one-way remotes. The remote controls for the CS-2004DC & CS-2004TW1 systems
ARE NOT interchangeable.
Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding
remotes, ALL your system’s remote codes must be learned at time of programming! These systems allow storage
of up to 4 different remote codes in memory. Note the slightly difference in program step #4 for either a2004DC or a
2004TW1 system on the next page.
13