Desa GN30 ユーザーズマニュアル
107884
For more information, visit www.desatech.com
For more information, visit www.desatech.com
14
TO TURN OFF GAS TO APPLIANCE
OPERATING HEATER
Continued
1.
Remove front panel (see Figure 7, page 8).
2.
Follow steps 1 through 5 under Lighting Instructions, page 13.
3.
With control knob pressed in, strike match. Hold match to
pilot until pilot lights.
pilot until pilot lights.
4.
Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob. Now follow
step 8, under Lighting Instructions, page 13.
pilot. After 30 seconds, release control knob. Now follow
step 8, under Lighting Instructions, page 13.
5.
Replace front panel.
MANUAL LIGHTING PROCEDURE
OPERATING HEATER (MANUAL CONTROL MODELS)
To Turn Off Gas To Appliance
Manual Lighting Procedure
Manual Lighting Procedure
OPERATING HEATER (THERMOSTAT CONTROLLED MODELS)
For Your Safety Read Before Lighting
Lighting Instructions
Lighting Instructions
Shutting Off Heater
1.
Press in and turn control knob clockwise
to the
PILOT position.
2.
Turn control knob clockwise
to the OFF position.
3.
Turn off all electric power to the appliance if service is to
be performed.
be performed.
Shutting Off Burner Only (pilot stays lit)
Turn control knob clockwise
to the PILOT position.
LIGHTING INSTRUCTIONS
1.
STOP! Read the safety information, column 1.
2.
Make sure equipment shutoff valve is fully open.
3.
Turn control knob clockwise
to the OFF position.
4.
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information, column 1. If you don’t
smell gas, go to the next step.
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information, column 1. If you don’t
smell gas, go to the next step.
5.
Turn control knob counterclockwise
to the PI-
LOT position. Press in control knob for five (5) seconds
(see Figure 21, page 15).
(see Figure 21, page 15).
Note:
You may be running this heater for the first time
after hooking up to gas supply. If so, the control knob may
need to be pressed in for 30 seconds or more. This will al-
low air to bleed from the gas system.
• If control knob does not pop up when released, contact a
need to be pressed in for 30 seconds or more. This will al-
low air to bleed from the gas system.
• If control knob does not pop up when released, contact a
qualified service person or gas supplier for repairs.
6.
With control knob pressed in, push down and release igni-
tor button. This will light pilot. The pilot is attached to the
front of burner. The pilot is attached to the front of the burner.
If needed, keep pressing ignitor button until pilot lights.
tor button. This will light pilot. The pilot is attached to the
front of burner. The pilot is attached to the front of the burner.
If needed, keep pressing ignitor button until pilot lights.
Note:
If pilot does not stay lit, refer to Troubleshooting,
pages 17 through 19. Also contact a qualified service per-
son or gas supplier for repairs. Until repairs are made, light
pilot with match. To light pilot with match, see Manual
Lighting Procedure, page 15.
son or gas supplier for repairs. Until repairs are made, light
pilot with match. To light pilot with match, see Manual
Lighting Procedure, page 15.
7.
Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob.
• If control knob does not pop up when released, contact a
pilot. After 30 seconds, release control knob.
• If control knob does not pop up when released, contact a
qualified service person or gas supplier for repairs.
Note:
If pilot goes out, repeat steps 3 through 7. This
heater has a safety interlock system. Wait one (1) minute
before lighting pilot again.
before lighting pilot again.
8.
Turn control knob counterclockwise
to desired
heating level. The main burner should light. Set control
knob to any heat level between HI and LO.
knob to any heat level between HI and LO.
THERMOSTAT CONTROLLED MODELS
FOR YOUR SAFETY READ
BEFORE LIGHTING
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire de-
partment.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
erty damage, personal injury or loss of life.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don’t try to repair it, call a qualified service techni-
cian or gas supplier. Force or attempted repair may result
in a fire or explosion.
hand, don’t try to repair it, call a qualified service techni-
cian or gas supplier. Force or attempted repair may result
in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
the appliance and to replace any part of the control system
and any gas control which has been under water.