Desa FVFM27NR/PR ユーザーズマニュアル
3
108382
OWNER’S MANUAL
For more information, visit www.desatech.com
PRODUCT IDENTIFICATION
LOCAL CODES
Install and use heater with care. Follow all
local codes. In the absence of local codes, use
the latest edition of The National Fuel Gas
Code, ANSI Z223.1/NFPA 54*.
local codes. In the absence of local codes, use
the latest edition of The National Fuel Gas
Code, ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
Note:
Where listed vented decorative logs
are required, thermostat operation is not
permitted.
permitted.
UNPACKING
CAUTION: Do not remove the
metal data plates from the grate
assembly. The data plates contain
important product information.
assembly. The data plates contain
important product information.
1.
Remove logs and heater base assem-
bly from carton.
bly from carton.
Note:
Do not pick up
heater base assembly by the burner.
This could damage heater. Always
handle base assembly by grate.
This could damage heater. Always
handle base assembly by grate.
2.
Remove all protective packaging ap-
plied to logs and heater for shipment.
plied to logs and heater for shipment.
3.
Check all items for any shipping dam-
age. If damaged, promptly inform
dealer where you bought heater.
age. If damaged, promptly inform
dealer where you bought heater.
PRODUCT
FEATURES
FEATURES
OPERATION
This heater is clean burning. It requires no
outside venting. There is no heat loss out a vent
or up a chimney. Heat is generated by realistic,
dancing yellow flames. This heater is de-
signed for vent-free operation with flue damper
closed. It has been tested and approved to
ANSI Z21.11.2 standard for unvented heaters.
State and local codes in some areas prohibit
the use of vent-free heaters. This heater may
also be operated as a vented decorative prod-
uct (ANSI Z21.60) by opening flue damper
(non-thermostat operation only).
outside venting. There is no heat loss out a vent
or up a chimney. Heat is generated by realistic,
dancing yellow flames. This heater is de-
signed for vent-free operation with flue damper
closed. It has been tested and approved to
ANSI Z21.11.2 standard for unvented heaters.
State and local codes in some areas prohibit
the use of vent-free heaters. This heater may
also be operated as a vented decorative prod-
uct (ANSI Z21.60) by opening flue damper
(non-thermostat operation only).
APPLICATION
These multisided logs are designed to be
equally beautiful when viewed from any angle.
equally beautiful when viewed from any angle.
They are designed specifically for use in
see-through, peninsula, and island fireboxes
with multiple openings. You may also in-
stall this log heater in a standard firebox.
see-through, peninsula, and island fireboxes
with multiple openings. You may also in-
stall this log heater in a standard firebox.
SAFETY PILOT
This heater has a pilot with an Oxygen Deple-
tion Sensing (ODS) safety shutoff system.
The ODS/pilot is a required feature for vent-
free room heaters. The ODS/pilot shuts off
the heater if there is not enough fresh air.
tion Sensing (ODS) safety shutoff system.
The ODS/pilot is a required feature for vent-
free room heaters. The ODS/pilot shuts off
the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system
requires no matches, batteries, or other
sources to light heater.
requires no matches, batteries, or other
sources to light heater.
REMOTE CONTROL
ACCESSORIES
ACCESSORIES
There are four optional remote controls that
can be purchased separately for this log heater:
can be purchased separately for this log heater:
• wall switch
• wall thermostat
• hand-held ON/OFF remote
• hand-held thermostat remote
See Accessories, page 24.
NOTE:
The wall thermostat or hand-held
thermostat may not be used where vented
decorative listing is required.
decorative listing is required.
SAFETY
INFORMATION
INFORMATION
Continued
13. Do not use this heater to cook food or
burn paper or other objects.
14. Do not use heater if any part has been
exposed to or under water. Immediately
call a qualified service technician to in-
spect the room heater and to replace any
part of the control system and any gas
control which has been under water.
call a qualified service technician to in-
spect the room heater and to replace any
part of the control system and any gas
control which has been under water.
15. Do not operate heater if any log is bro-
ken. Do not operate heater if a log is
chipped (dime-sized or larger).
chipped (dime-sized or larger).
16. Turn heater off and let cool before ser-
vicing, installing, or repairing. Make sure
the selector switch is in the OFF posi-
tion. Only a qualified service person
should install, service, or repair heater.
the selector switch is in the OFF posi-
tion. Only a qualified service person
should install, service, or repair heater.
17. Make sure the selector switch is in the
OFF position when you are away from
home for long periods of time.
home for long periods of time.
18. This heater must not be connected to
any external electrical source.
19. Operating heater above elevations of
4,500 feet could cause pilot outage.
20. Provide adequate clearances around air
openings.
AU
TO
ON
OF
F
CO
OL
ER
W
AR
ME
R
TE
MP
Figure 1 - Product Identification
Control Knob
Piezo
Ignitor
Ignitor
Log Set
Base Assembly
Optional
Remote
Control
Remote
Control
Flame
Adjustment
Knob
Adjustment
Knob
Optional
Selector
Switch
Selector
Switch