Dimplex LBN20 プリント
Installation in a Fireplace Opening
At the rear of the fire, two adjustable supports are
provided for leveling the fire where the base of the
fireplace opening is raised above the level of the
hearth.
provided for leveling the fire where the base of the
fireplace opening is raised above the level of the
hearth.
Adjust by removing the two screws holding each
bracket in position, then refit the bracket and the two
screws in the required position.
bracket in position, then refit the bracket and the two
screws in the required position.
Operation
The unique flame effect may be enjoyed whether or
not the heating elements are in operation.
'Please note: Used in an environment where
background noise is very low, it may be possible to
hear the fan which operates the flame effect. This is
normal and should not be a cause for concern'.
not the heating elements are in operation.
'Please note: Used in an environment where
background noise is very low, it may be possible to
hear the fan which operates the flame effect. This is
normal and should not be a cause for concern'.
Controls
The heater controls are located on the right hand side
beneath the hinged canopy cover.
Raise the canopy cover to access the controls.
Three switches provide a choice of heat settings and
an adjustable thermostat enables the room
temperature to be controlled by adjusting the setting
accordingly.
A switch is in the ON position when the red indicator
mark on the switch is visible.
Switch 1 - Controls the electricity
beneath the hinged canopy cover.
Raise the canopy cover to access the controls.
Three switches provide a choice of heat settings and
an adjustable thermostat enables the room
temperature to be controlled by adjusting the setting
accordingly.
A switch is in the ON position when the red indicator
mark on the switch is visible.
Switch 1 - Controls the electricity
supply to the heater
and the flame effect.
Note: This switch must
be in the ON position
for the heater to
operate.
and the flame effect.
Note: This switch must
be in the ON position
for the heater to
operate.
Switch 2 - Provides 1kw heat output, with thermostat
control.
Switch 3 – Provides 2kw heat output with switch 2, with
thermostat control
control.
Switch 3 – Provides 2kw heat output with switch 2, with
thermostat control
Setting the Thermostat
Plug in and set all switches to ON. Turn the thermostat
knob to MAX to warm the room rapidly. When the
room temperature has reached the desired level, turn
the thermostat knob back slowly until the thermostat
just clicks off. The heater will then maintain the room
temperature at the chosen level.
NOTE – Should your heater fail to come on when the
thermostat is at a low setting, this may be due to the
room temperature being higher than the thermostat
setting.
knob to MAX to warm the room rapidly. When the
room temperature has reached the desired level, turn
the thermostat knob back slowly until the thermostat
just clicks off. The heater will then maintain the room
temperature at the chosen level.
NOTE – Should your heater fail to come on when the
thermostat is at a low setting, this may be due to the
room temperature being higher than the thermostat
setting.
Maintenance
WARNING – BEFORE UNDERTAKING ANY
MAINTENANCE OR CLEANING REMOVE PLUG OR
DISCONNECT FROM THE ELECTRICITY SUPPLY.
MAINTENANCE OR CLEANING REMOVE PLUG OR
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Lamp Replacement
There are two lamps located beneath the fuel effect.
To gain access to the lamp, the grate / fuel effect
secured by two screws, must be removed. (See Fig.1)
Remove the coal and carefully lift the grate / fuel effect
clear and set aside.
Replace the defective lamp with a 240V 60 Watt E14
SES clear candle lamp.
Replace grate/fuel effect, secure with screws.
To gain access to the lamp, the grate / fuel effect
secured by two screws, must be removed. (See Fig.1)
Remove the coal and carefully lift the grate / fuel effect
clear and set aside.
Replace the defective lamp with a 240V 60 Watt E14
SES clear candle lamp.
Replace grate/fuel effect, secure with screws.
Safety cut-out
For your safety, this appliance has been fitted with
thermal cut-out. In the event that the product
overheats, the cut-out switches the heat off
automatically.
To bring the heat back into operation, remove the
cause of the overheating, then unplug or turn off the
electrical supply to the heater for up to 10 minutes.
When the heater has cooled sufficiently, re-connect
and switch on the heater.
thermal cut-out. In the event that the product
overheats, the cut-out switches the heat off
automatically.
To bring the heat back into operation, remove the
cause of the overheating, then unplug or turn off the
electrical supply to the heater for up to 10 minutes.
When the heater has cooled sufficiently, re-connect
and switch on the heater.
Cleaning
Before commencing cleaning, unplug the heater and
allow it to cool.
The surfaces of the heater should be given an
occasional wipe over with a dry soft cloth.
Do not use detergents, abrasive cleaning powder or
polish on the metal body of the heater.
The glass screen should be cleaned carefully with a
chamois leather. DO NOT use proprietary cleaners.
To remove any accumulation of dust or fluff the soft
brush attachment of a vacuum cleaner should
occasionally be used to clean the outlet grille of the fan
heater located under the canopy.
To clean the fuel effect, remove the coal pieces and
wash in warm water. The plastic tray should be wiped
clean with a damp cloth. When dry replace the coal
pieces and arrange for best effect.
allow it to cool.
The surfaces of the heater should be given an
occasional wipe over with a dry soft cloth.
Do not use detergents, abrasive cleaning powder or
polish on the metal body of the heater.
The glass screen should be cleaned carefully with a
chamois leather. DO NOT use proprietary cleaners.
To remove any accumulation of dust or fluff the soft
brush attachment of a vacuum cleaner should
occasionally be used to clean the outlet grille of the fan
heater located under the canopy.
To clean the fuel effect, remove the coal pieces and
wash in warm water. The plastic tray should be wiped
clean with a damp cloth. When dry replace the coal
pieces and arrange for best effect.
After Sales Service
Your product is guaranteed for one year from the date
of purchase. We undertake to exchange or repair free
of charge within this period, any part (excluding lamps)
found to be defective due to manufacturing fault.
Should you require after sales service, please get in
touch with the supplier through whom you purchased
the appliance or your nearest Service Agent.
of purchase. We undertake to exchange or repair free
of charge within this period, any part (excluding lamps)
found to be defective due to manufacturing fault.
Should you require after sales service, please get in
touch with the supplier through whom you purchased
the appliance or your nearest Service Agent.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, N60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 9/336
(EMC) EN55014, N60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 9/336
Glen Dimplex UK Limited
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Millbrook House
Grange Drive
Grange Drive
Customer Services: Tel. 0870 7270101
Hedge End
Fax. 0870 7270102
Southampton
E-mail. customer.services@glendimplex
Hampshire. SO30 2DF
Republic of Ireland 01. 8424833
Please do not initially return a faulty appliance or part
of an appliance to us as this may result in transit
damage and/or delay in providing service. Let us know
your difficulty quoting the model number and series
letter of the appliance. We will then take the
appropriate action.
of an appliance to us as this may result in transit
damage and/or delay in providing service. Let us know
your difficulty quoting the model number and series
letter of the appliance. We will then take the
appropriate action.