Alen MDF-50AE ユーザーズマニュアル
4
CONTROL PADS ON THE DEHUMIDIFIER
1
1
2
2
3
3
4
4
5
5
Power on
indicator light
indicator light
Continuous
operation on
indicator light
operation on
indicator light
Bucket full
indicator light
indicator light
High fan
indicator
light
indicator
light
Normal fan
indicator light
indicator light
Control pads
1
1
POWER Pad
Press to turn the dehumidifier on and off.
2
2
Continue Pad
Select for the dehumidifier to operate
continuously for maximum dehumidification
until the bucket is full. The Humdity set
control pads cannot be used when
Continuous operation is on.
continuously for maximum dehumidification
until the bucket is full. The Humdity set
control pads cannot be used when
Continuous operation is on.
3
3
Humidity Set Control Pads
The humidity level can be set within a
range of 35%RH(Relative Humidity) to
80%RH(Relative Humidity) in 5%
increments.
For drier air, press the pad and set
to a lower percent value(%).
For damper air, press the pad and
set a higher percent value(%).
range of 35%RH(Relative Humidity) to
80%RH(Relative Humidity) in 5%
increments.
For drier air, press the pad and set
to a lower percent value(%).
For damper air, press the pad and
set a higher percent value(%).
4
4
Fan speed Pads
Control the fan speed. Press to select either High or Normal
fan speed. Set the fan control to High for maximum moisture
removal. When the humidity has been reduced and quiet
operation is preferred, set the fan control to Normal.
fan speed. Set the fan control to High for maximum moisture
removal. When the humidity has been reduced and quiet
operation is preferred, set the fan control to Normal.
5
5
Display
Shows the set % humidity level while setting, then shows
the actual(+5% accuracy) room % humidity level.
Error Codes:
E1- Humidity sensor error--Unplug the unit and plug it back
in. If error repeats, call for service.
E2- Temperature sensor error-- Unplug the unit and plug it
back in. If error repeats, call for service.
P1- Unit is defrosting-- Allow the unit time to automatically
defrost. The error will clear after the unit self defrosts.
P2- Bucket is full-- Empty the bucket and replace in
the right position.
the actual(+5% accuracy) room % humidity level.
Error Codes:
E1- Humidity sensor error--Unplug the unit and plug it back
in. If error repeats, call for service.
E2- Temperature sensor error-- Unplug the unit and plug it
back in. If error repeats, call for service.
P1- Unit is defrosting-- Allow the unit time to automatically
defrost. The error will clear after the unit self defrosts.
P2- Bucket is full-- Empty the bucket and replace in
the right position.
Other features
Bucket Full Light
Glows when the bucket is ready to be
emptied, or when the bucket is removed
or not replaced in the proper position.
emptied, or when the bucket is removed
or not replaced in the proper position.
Auto Shut Off
The water level control switch shuts off the
dehumidifier when the bucket is full, or when
the bucket is removed or not replaced in the
proper position. When the setting humidity
is reached, the unit will be shut off automatically.
dehumidifier when the bucket is full, or when
the bucket is removed or not replaced in the
proper position. When the setting humidity
is reached, the unit will be shut off automatically.
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue to
run until the frost disappears.
compressor will cycle off and the fan will continue to
run until the frost disappears.
Power Outage
In the case of a power outage or interruption, the unit will
automatically re-start, in the settings last used, after the
power is restored.
automatically re-start, in the settings last used, after the
power is restored.
Auto Defrost
C
Power
Continuous
Full
Humidity%
Turbo
Normal
Fig.1