Sony 900 ユーザーズマニュアル
7
Chapter 7 Location and Function of Parts and Controls
78
HDC-900/950/930 Series Product Information Manual
f
Cable clamp
Used to secure the fiber optic cable. The clamp is
designed for the FC2-PD50 and FC2-PD250.
designed for the FC2-PD50 and FC2-PD250.
g
Accessory bracket
Used to secure optional accessories such as the BKP-
7911/7912 Script Holder or Focus/Zoom Demand.
7911/7912 Script Holder or Focus/Zoom Demand.
For more information on attaching an accessory, see the
accessory’s operation manual.
accessory’s operation manual.
h
AUDIO IN CH-1 and CH-2 connectors (XLR 3-pin)
Used to input microphone or line signals.
i
AUDIO IN switch
Set this switch according to the device connected to
the AUDIO IN CH-1 and CH-2 connectors.
the AUDIO IN CH-1 and CH-2 connectors.
MIC
: When connecting microphones
LINE
: When connecting line signal sources
j
Microphone power switches
For the microphones connected to the AUDIO IN CH-
1 and CH-2 connectors, respectively.
1 and CH-2 connectors, respectively.
+48 V
: When the connected microphone requires an
external power source. A power of +48 V is supplied
to the microphone.
to the microphone.
OFF
: When the connected microphone requires no
external power.
Note
To supply a power of +12 V, modification of the camera
is required. For details, refer to the Installation &
Maintenance Manual. Note that the modification must
be performed by service personnel.
is required. For details, refer to the Installation &
Maintenance Manual. Note that the modification must
be performed by service personnel.
k
PROMPTER connector (BNC type)
Used to output the signal input from the HDCU-900
Camera Control Unit’s PROMPTER INPUT connector.
Camera Control Unit’s PROMPTER INPUT connector.
l
TEST OUT (test signal output) connector (BNC
type)
type)
Used to output the signal selected by the video signal
select buttons on the rear panel. If the RET 1 or RET 2
button is pushed in, the output will be a return video
signal.
select buttons on the rear panel. If the RET 1 or RET 2
button is pushed in, the output will be a return video
signal.
m
REMOTE connector (8-pin)
Used to connect the camera to an optional MSU-700A/
750 Master Setup Unit or RCP-700 series Remote
Control Panel, via a CCA cable. The connected unit
may then control the HDC-900.
750 Master Setup Unit or RCP-700 series Remote
Control Panel, via a CCA cable. The connected unit
may then control the HDC-900.
n
TRACKER connector (20-pin)
Used for communication between the camera operator
and the tracker, and also for intercom channels 1 and
2. It also supplies the up tally signal and the program
audio signal.
and the tracker, and also for intercom channels 1 and
2. It also supplies the up tally signal and the program
audio signal.
o
RET (return video) CONTROL connector (6-pin)
This connector allows an external controller to switch
return video 1, 2, and 3, as well as turn the intercom
microphone on and off.
return video 1, 2, and 3, as well as turn the intercom
microphone on and off.
p
DC OUT connector (4-pin)
Used to supply power (12 V, 5 W maximum) to a script
light of the BKP-7911/7912 Script Holder.
light of the BKP-7911/7912 Script Holder.
q
CCU (camera control unit) connector (electro
optical multi-connector)
optical multi-connector)
Connect to the CAMERA connector of the HDCU-900
Camera Control Unit using an electro-optical
composite cable. Power and video, audio, and control
signals are passed between the camera and the
control unit using just one cable.
Camera Control Unit using an electro-optical
composite cable. Power and video, audio, and control
signals are passed between the camera and the
control unit using just one cable.
r
DC IN connector (4-pin)
Connect to a DC power source (10.5 to 17 V) when
using the HDC-900 as a stand-alone unit.
using the HDC-900 as a stand-alone unit.
s
AC OUT connector
Used to supply AC power (200 VA maximum).
t
VTR connector (26-pin)
When using the camera in stand-alone use, a VTR can
be connected using an HDCZ cable to this connector.
In this case, however, the VTR cannot be started or
stopped from the camera.
be connected using an HDCZ cable to this connector.
In this case, however, the VTR cannot be started or
stopped from the camera.
u
HD SERIAL OUT connector
A serial digital interface with a transfer speed of 1.5
Gbps, this connector may be used to output a video
signal to a monitor or VTR.
Gbps, this connector may be used to output a video
signal to a monitor or VTR.