Empire Products BF-10-2 ユーザーズマニュアル
Page 18
16012-1-0504
. ...
PARTS LIST
Wiring
The appliance, when installed, must be electrically grounded in accor-
dance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, if an external electrical
source is utilized. This appliance is equipped with a three-prong
[grounding] plug for your protection against shock hazard and
should be plugged directly into a properly grounded three-prong
receptacle. Do not cut or remove the grounding prong from this plug.
For an ungrounded receptacle, an adapter, which has two prongs and a
wire for grounding, can be purchased, plugged into the ungrounded
receptacle and its wire connected to the receptacle mounting screw. With
this wire completing the ground, the appliance cord plug can be plugged
into the adapter and be electrically grounded.
The appliance, when installed, must be electrically grounded in accor-
dance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, if an external electrical
source is utilized. This appliance is equipped with a three-prong
[grounding] plug for your protection against shock hazard and
should be plugged directly into a properly grounded three-prong
receptacle. Do not cut or remove the grounding prong from this plug.
For an ungrounded receptacle, an adapter, which has two prongs and a
wire for grounding, can be purchased, plugged into the ungrounded
receptacle and its wire connected to the receptacle mounting screw. With
this wire completing the ground, the appliance cord plug can be plugged
into the adapter and be electrically grounded.
CAUTION: Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous opera-
tion. Verify proper operation after servicing.
controls. Wiring errors can cause improper and dangerous opera-
tion. Verify proper operation after servicing.
Blower Motor
The blower motor does not have oiling holes. Do not attempt to oil the
blower motor.
The blower motor does not have oiling holes. Do not attempt to oil the
blower motor.
Blower Wheel
The blower wheel will collect lint and could require periodic cleaning. If
the air output decreases or the noise level increases, it indicates a dirty
blower wheel.
The blower wheel will collect lint and could require periodic cleaning. If
the air output decreases or the noise level increases, it indicates a dirty
blower wheel.
To clean blower wheel:
1.
1.
Turn OFF gas supply to the heater.
2.
Turn OFF electrical supply to the heater.
3.
Remove lower louver from casing assembly (2 screws).
4.
Remove reflector from casing assembly (2 screws).
5.
Remove upper louver from casing assembly (2 screws).
6.
Clean blower wheel with a vacuum cleaner.
7.
As parts are being replaced in reverse order, check for gas leaks at
all gas connections before lower louver is replaced onto casing
assembly.
all gas connections before lower louver is replaced onto casing
assembly.
WARNING:
Unplugging of blower accessory will not stop the heater from
cycling. To turn off gas to the unvented heater: Push in gas
control knob slightly and turn clockwise to "OFF." Do not
force.
Unplugging of blower accessory will not stop the heater from
cycling. To turn off gas to the unvented heater: Push in gas
control knob slightly and turn clockwise to "OFF." Do not
force.
If any of the original wire as
supplied with the appliance
must be replaced, it must be
replaced with type 125°C wire
or its equivalent.
supplied with the appliance
must be replaced, it must be
replaced with type 125°C wire
or its equivalent.
INDEX
PART
NO.
NO.
DESCRIPTION
1
R-2396
BLOWER (INCLUDES MOTOR, FAN,
AND FAN HOUSING)
AND FAN HOUSING)
2
R-2503
FAN CONTROL
3
R-2395 WIRE ASSEMBLY
4
R-1468
BUSHING - HEYCO #SR5KN4
5
VF-068
CORD SET ASSEMBLY
6
SR-196 BLOWER PAN (BF-10 BF-20)
6
SR-198
BLOWER PAN (BF-30)
7
R-1499
RUBBER GROMMET (4 REQUIRED)
8
R-1454
BRASS BUSHING (4 REQUIRED)
NOT SHOWN
SR-219
BLOWER HARDWARE PACKAGE
OPTIONAL BLOWER INSTALLATION INSTRUCTIONS (continued)