Friedrich 920-087-09 ユーザーズマニュアル

ページ / 36
27
q
  Inspect and ensure that all components and accessories have been 
installed properly and that they have not been damaged during the 
installation process.
q
  Check the condensate water drain(s) to ensure they are adequate for 
the removal of condensate water, and that they meet the approval of 
the end user.
q
  Ensure that all installations concerning clearances around the unit 
have been adhered to.  Check to ensure that the unit air filter, indoor 
coil, and outdoor coil are free from any obstructions.
q
  Ensure that the entire installation is in compliance with all applicable 
national and local codes and ordinances that have jurisdiction.
q
  Secure components and accessories, such as the chassis, decorative 
front cover and control door.
q
  Start the unit and check for proper operation of all components in 
each mode of operation.  Instruct the owner or operator of this units 
operation, and the manufacturer’s recommended routine maintenance 
schedule.
NOTE: 
A log for recording the dates of maintenance and/or service 
is recommended.
q
  Present the owner or operator of the equipment with the Installation 
& Operation manual, all accessory installation instructions, and the 
name, address and telephone number of the Authorized Friedrich 
Warranty  Service  Company  in  the  area  for  future  reference  if 
necessary.
Final Inspection & Start-up Checklist
Routine Maintenance
To ensure proper unit operation and life expectancy the following mainte-
nance procedures should be performed on a regular basis.
however, you must be careful not to bend the aluminium fin pack.  Use a 
sweeping up and down motion in the direction of the vertical aluminium 
fin pack when pressure cleaning coils.
NOTE:  It is extremely important to insure that none of the electrical 
and/or electronic parts of the unit get wet. Be sure to cover all electrical 
components to protect them from water or spray.
Decorative Front
The decorative front and discharge air grille may be cleaned with a mild 
soap or detergent. Do NOT use solvents or hydrocarbon based cleaners 
such as acetone, naphtha, gasoline, benzene, etc., to clean the decorative 
front or air discharge grilles.
Use a damp (not wet) cloth when cleaning the control area to prevent 
water from entering the unit, and possibly damaging the electronic control.
Fan Motor & Compressor
The fan motor & compressor and are permanently lubricated, and require 
no additional lubrication.
Wall Sleeve
Inspect the inside of the wall sleeve and drain system periodically (annually 
or semi-annually) and clean as required.
Under extreme conditions, more frequent cleaning may be necessary.  
Clean both of these areas with an antibacterial and antifungal cleaner. 
Rinse both items thoroughly with water and ensure that the drain outlets 
are operating correctly. Check the sealant around the sleeve and reseal 
areas as needed.
Air Filter
To ensure proper unit operation, the air filters should be cleaned at least 
monthly, and more frequently if conditions warrant. The unit must be turned 
off before the filters are cleaned.
To remove the air filters, grasp the top of the filter and lift out of the front 
cabinet. Reverse the procedure to reinstall the filters.
Clean the filters with a mild detergent in warm water, and allow them to dry 
thoroughly before reinstalling.
Coils & Chassis
NOTE:  Do not use a caustic coil cleaning agent on coils or base pan. 
Use a biodegradable cleaning agent and degreaser.  The use of harsh 
cleaning materials may lead to deterioration of the aluminum fins or the 
coil end plates.
The indoor coil and outdoor coils and base pan should be inspected pe-
riodically (annually or semi-annually) and cleaned of all debris (lint, dirt. 
leaves, paper, etc.) as necessary.  Under extreme conditions, more frequent 
cleaning may by required.  Clean the coils and base pan with a soft brush 
and compressed air or vacuum.  A pressure washer may also be used, 
WARNING 
Electrical Shock Hazard
Unplug Unit or turn off electrical power
to unit prior to performing maintenance
procedures.
Failure to do so can result in electrical
shock or death.