American Power Conversion Central Air Conditioning System ユーザーズマニュアル
Operation: Respond to Alarms
42
NetworkAIR IR Operation, Maintenance, and Troubleshooting
Env Temperature Low
• Verify that no supply air is fed directly back into the return air.
• Ensure that the alarm delay is not set too low. The delay should be long
• Ensure that the alarm delay is not set too low. The delay should be long
enough to allow the room temperature to stabilize after start-up.
• Verify that the temperature alarm threshold for the environmental (return or
remote) sensors is below the cool and reheat setpoints.
• Verify that the Module is configured and equipped for the reheat mode.
• Ensure that the reheat mode is enabled (if your Module is equipped with
• Ensure that the reheat mode is enabled (if your Module is equipped with
reheat).
• Ensure that the reheat mode is not disabled because of an active user-defined
input mapped to nonessential lockout.
Fire Detected
• Follow the appropriate facility emergency protocol. N
OTE
: The purpose of
the fire sensor is to warn you of possible equipment damage. It is NOT
intended to provide a fire alarm system to protect the facility and the lives of
its occupants.
intended to provide a fire alarm system to protect the facility and the lives of
its occupants.
• Confirm that the wiring connections are secured to the wiring harness.
• Verify the setting of the fire detector (fire stat).
• Replace the fire detector (fire stat).
• Verify the setting of the fire detector (fire stat).
• Replace the fire detector (fire stat).
Fluid Coil Actuator Fail
• Verify that the connections between the actuator and the controller board are
correct and securely tightened.
• Confirm that the control voltage and signal voltage reach the actuator.
• Ensure that the proper Module configuration is defined for this Module,
• Ensure that the proper Module configuration is defined for this Module,
especially that the coil configuration and the actuator type are correct.
• Replace the Coil Fluid Actuator.
Group Configuration Invalid
• Check that the # Systems setting (Path: Main > Setup > Group > Group
Config) agrees with the actual number of Systems connected to the Group.
Increase this setting to match the number of connected Systems.
Increase this setting to match the number of connected Systems.
Group Configuration Conflict
• Verify the Group configuration settings (Path: Main > Setup > Group) are
correct. The Group detected one or more Systems in the Group to have
different Group configuration settings and changed that System’s settings.
different Group configuration settings and changed that System’s settings.
Group Fatal Fire Shutdown
• Check the Systems in this Group for fire alarms. The Group Fatal Fire
Shutdown occurs only when the Group Fire Alarm configuration setting
(Path: Main > Setup > Group Config > Grp Fire Alrm) is On. While the
fire alarm is active, the Group will remain shut down.
(Path: Main > Setup > Group Config > Grp Fire Alrm) is On. While the
fire alarm is active, the Group will remain shut down.
Group Fatal Smoke Shutdown
• Check the Systems in this Group for smoke alarms. The Group Fatal Smoke
Shutdown occurs only when the Group Smoke Alarm configuration setting
(Path: Main > Setup > Group Config > Grp Smoke Alrm) is On. While
the smoke alarm is active, the Group will remain shut down.
(Path: Main > Setup > Group Config > Grp Smoke Alrm) is On. While
the smoke alarm is active, the Group will remain shut down.
Heater Requires Maintenance
• Verify the operation of the heater and perform preventive maintenance.
• Reset the maintenance alarm on the display interface for the heater.
• Reset the maintenance alarm on the display interface for the heater.
Humidifier Current High
• Verify that the proper voltage is applied to the humidifier cylinder.
• Confirm that the line voltage connections to the cylinder are secure and
• Confirm that the line voltage connections to the cylinder are secure and
correct.
• Ensure that the humidifier water supply has not been conditioned.
Conditioning can increase the water conductivity.
• Check the humidifier cylinder for mineral buildup that bridges the electrodes.
• Check the fill and drain valves for leaks.
• Check the fill and drain valves for leaks.
Displayed Alarm Message
Action Required