Ei Electronics Ei156TLH プリント
Shannon Free Zone, Shannon, Co. Clare, Ireland.
Ph.
+353 61 471277
Fx.
+353 61 471053
Email.
eielectronics@eiltd.ie
Web:
www.eielectronics.com
E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice
.
Ei156TLH DataSht RevB
Model
Ei156TLH Optical
Installation & Placement
Wiring for Interconnected Alarms
Be very careful about correctly wiring the alarms as mixing Live and Neutral
will blow/damage interconnected alarms.
Alarms should be placed in accordance with the general guidelines shown in
the diagram above. These recommendations are based on the problem of
areas of “dead air” close to corners of rooms and apexes of ceilings, which
could result in the prevention of smoke reaching the smoke detector
Please consult instruction booklet for specific installation details
will blow/damage interconnected alarms.
Alarms should be placed in accordance with the general guidelines shown in
the diagram above. These recommendations are based on the problem of
areas of “dead air” close to corners of rooms and apexes of ceilings, which
could result in the prevention of smoke reaching the smoke detector
Please consult instruction booklet for specific installation details
Important Precaution:
Do not install the actual smoke/heat
alarm itself in new or renovated
buildings until all work is completed
(including floor coverings) and the
building has been fully cleaned.
The wiring can be installed when
appropriate. (Excessive dust and
debris from building work can
contaminate the smoke chamber
and cause problems, and it will also
invalidate the guarantee). If it must
be installed, cover it completely,
particularly around the edges, with
a dust cover (eg. a plastic bag),
until all cleaning is finished..
Connect wires to the unit as in
wiring diagram. All wiring must
comply with local codes.
alarm itself in new or renovated
buildings until all work is completed
(including floor coverings) and the
building has been fully cleaned.
The wiring can be installed when
appropriate. (Excessive dust and
debris from building work can
contaminate the smoke chamber
and cause problems, and it will also
invalidate the guarantee). If it must
be installed, cover it completely,
particularly around the edges, with
a dust cover (eg. a plastic bag),
until all cleaning is finished..
Connect wires to the unit as in
wiring diagram. All wiring must
comply with local codes.
Technical Specification
Sensor
Optical, uses light scatter from
smoke
smoke
Sensitivity:
Complies with BS 5446 Part 1:
2000
2000
Source:
Contains no radioactive material
Airspeed:
Essentially immune to the effect
of airspeed.
Button Test:
Simulates the effect of smoke and
checks chamber, electronics and
horn.
checks chamber, electronics and
horn.
Ambient Light:
Chamber housing design and
compensation overcomes
problems with stray light.
compensation overcomes
problems with stray light.
Automatic Self-Test:
Smoke Chamber is tested every 40
Sec. and unit beeps (without LED
flash) if it is degraded.
Insect Screen:
Prevents insects or debris entering
chamber (1.00mm mesh size)
chamber (1.00mm mesh size)
Supply Voltage:
230V AC
Battery back up:
Rechargeable lithium cells
Power-On Indicator:
Continuous green LED
Alarm:
Electronic Piezoelectric horn
Alarm Sound Output:
85dB (minimum) at 3m
Alarm Status:
Red LED flashes every second on
unit sensing fire
Temperature Range:
0° to 40°C
Humidity Range:
15% to 95% Relative Humidity
Interconnect:
Up to 12 interconnected
Ei150/151TLR/154TL/155/156TLH/
156TLR smoke or heat alarms,
along with an EI158 relay base
Ei150/151TLR/154TL/155/156TLH/
156TLR smoke or heat alarms,
along with an EI158 relay base
Fixing:
Screw fixings supplied
Plastic material:
UL94VO flame retardant
Dimensions:
140mm x 120mm x 46mm
Weight:
218g
Warranty:
5 year (limited) warranty
Approvals:
Kitemarked to BS EN 14604:2005,
CE Approved
CE Approved
Specifications are subject to change