American Standard 2262 ユーザーズマニュアル
RUBBER
GASKET
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
BOLTS PRE-
INSTALLED
NUT
WASHER
6
8
7a
7b
INSTALL TOILET
a.
Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on
floor.
Alternately tighten nuts until toilet is firmly seated on
floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b.
Install caps on washers. (If necessary, cut bolt height
to size before installing caps.)
c.
Smooth off the bead of sealant around base. Remove
excess sealant.
INSTALL TANK
a.
a.
Install large rubber gasket over
threaded outlet on bottom of tank
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening, and tank
mounting bolts go through mounting
holes. Secure with metal washers
and nuts.
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening, and tank
mounting bolts go through mounting
holes. Secure with metal washers
and nuts.
b.
With tank parallel to wall, alternately
tighten nuts until tank is snugged
down evenly against bowl surface.
down evenly against bowl surface.
INSTALL TANK
a.
a.
Install large rubber gasket over
threaded outlet on bottom of tank
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening.
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening.
b.
Insert tank mounting bolts and
rubber washers from inside tank,
through mounting holes, and secure
with metal washers and nuts.
through mounting holes, and secure
with metal washers and nuts.
c.
With tank parallel to wall, alternately
tighten nuts until tank is snugged
down evenly against bowl surface.
down evenly against bowl surface.
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
CLOSET FLANGE
CLOSET BOLT
NUT
WASHER
BOLT CAP
RUBBER
GASKET
GASKET
TANK MTG.
BOLTS
NUT
WASHER
!
!
- 2 -
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
For Tanks/Bowls using Speed
Connect System (Tank
mounting bolts pre-installed).
Connect System (Tank
mounting bolts pre-installed).
For all other Tanks/Bowls
RUBBER
WASHER
WASHER
7 3 0 4 5 1 - 1 0 0 R e v . A
CONNECT WATER SUPPLY
a.
Connect water supply line between
shutoff valve and tank water
inlet fitting. Tighten coupling nuts
securely. Check that refill tube is
inserted into overflow tube.
shutoff valve and tank water
inlet fitting. Tighten coupling nuts
securely. Check that refill tube is
inserted into overflow tube.
b.
Turn on supply valve and allow
tank to fill until water rises to
shutoff position.
tank to fill until water rises to
shutoff position.
c.
Check for leakage at fittings,
tighten or correct as needed.
tighten or correct as needed.
9
TANK
COUPLING NUT
FLEXIBLE
SUPPLY
SUPPLY
WATER INLET
COMPRESSION
COLLAR
COLLAR
WASHER
VALVE NUT
TRIM
PLATE
PLATE
VALVE
ADJUSTMENTS
a.
Adjust water level. Water level should be
adjusted to level indicated on tank by
adjusting valve height.
adjusting valve height.
See Step 11 for valve height adjustment
method
method
b.
If bowl fails to siphon, an adjustment may be
required with the lift chain. Simply remove the
bead chain from the retainment clip (see Fig.
10A) and take up slack on the chain, and
reinsert on lift rod. Make sure the chain is not
too taught.
bead chain from the retainment clip (see Fig.
10A) and take up slack on the chain, and
reinsert on lift rod. Make sure the chain is not
too taught.
TOILET REQUIRES THAT THE TANK
REFILLS IN NO LESS THAN ONE MINUTE.
ADJUST WATER SUPPLY VALVE (FIG. 9)
ACCORDINGLY.
REFILLS IN NO LESS THAN ONE MINUTE.
ADJUST WATER SUPPLY VALVE (FIG. 9)
ACCORDINGLY.
TRIP LEVER
WATER INLET
FLAPPER
ASSEMBLY
ASSEMBLY
OVERFLOW TUBE
WATER LINE LEVEL
WATER CONTROL
ASSEMBLY
REFILL TUBE
FLUSH VALVE
FLOAT
FLOAT
10
FLUSH VALVE
Fig. 10A