Marantz SR5005 ユーザーズマニュアル
66
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Operating learn mode
This remote control unit is capable of learning and storing codes used
by other remote controls that you already own.
For codes which are not learned, the remote control unit will transmit
either the Marantz preset codes from the initial settings, or remote
codes from another manufacturer’s AV equipment which is set by the
customer.
The receiver sensor for the remote control unit signals is located at the
top of the remote control unit.
by other remote controls that you already own.
For codes which are not learned, the remote control unit will transmit
either the Marantz preset codes from the initial settings, or remote
codes from another manufacturer’s AV equipment which is set by the
customer.
The receiver sensor for the remote control unit signals is located at the
top of the remote control unit.
This remote control unit is capable of learning around 160 codes.
NOTE
The learning procedure does not operate correctly if the batteries have
become worn.
become worn.
n
Learning procedure
1
Place the Marantz remote control and remote
control from the other device approximately 5 cm
apart, with the remote control signal transmission
sections facing each other.
2
Press and hold down
SET
and
SOURCE SEL
until the LEARN
indicator blinks.
3
Press input source select
buttons to select the input
source.
4
Select the button to be learned.
LEARN indicator lights up.
NOTE
• The learning function is unavailable for all
SOURCE
and
D.MODE
in
any mode.
• The learning function is unavailable for all buttons in TUNER mode
and AMP mode.
5
Press and hold the button of the original remote
control unit to be learned until the SEND indicator
blinks twice.
NOTE
• If the SEND indicator blinks once, repeat this step.
• If the LEARN indicator flashes when the SEND indicator is lit, then
• If the LEARN indicator flashes when the SEND indicator is lit, then
the button cannot be learned.
• When the memory of the remote control unit is full, the LEARN and
SEND indicators blink once. If you want to learn the code, you need
to erase a different learned button.
to erase a different learned button.
6
Repeat steps 4 and 5 to learn other buttons for the
same input source.
7
Repeat steps 3 to 6 to learn other input sources.
8
When programming of the remote control unit is
completed, press
SET
.
The LEARN display disappears, and the remote control unit
exits learn mode.
exits learn mode.
NOTE
• When the SEND indicator blinks once again, the transmitting code
is unavailable for remote control unit, or the transmitting signal has
been interrupted by noise.
been interrupted by noise.
• If no buttons are pressed for approximately 1 minutes while in the
LEARN mode, the remote control unit automatically exits from the
LEARN mode.
LEARN mode.
n
Erasing programmed codes
Codes can be erased in three ways: by buttons, sources, and by all
memory contents.
memory contents.
Erasing the code by buttons
1
Press and hold down
SET
and
SOURCE SEL
until the LEARN
indicator blinks.
2
Press input source select buttons
to select the input source you
want to delete.
3
Press and hold down
D.MODE
and press the learned button to
be erased twice.
SEND indicator blinks twice and the
mode returns to LEARN mode.
mode returns to LEARN mode.
4
To return the normal mode, press
SET
.
Erasing the code by SOURCE
1
Press and hold down
SET
and
SOURCE SEL
until the LEARN
indicator blinks.
2
Press and hold down
D.MODE
and press the learned input
source select buttons to be erased
twice.
LEARN indicator lights.
3
Press
ENTER
to continue erasing.
• The SEND indicator blinks twice and
the mode returns to LEARN mode.
• To cancel the erasing operation, do not
press
ENTER
, and simply press any
other button.
4
To return the normal mode,
press
SET
.
5 cm