Panasonic SCHT56 ユーザーズマニュアル
12
RQTX0175
a) Press and hold
.
[AUTO SPEAKER SETUP] indicator starts flashing.
“AUTO SETUP” appears on the display.
b) The unit checks that you have correctly
connected the calibration microphone.
c) The automatic setup starts with STEP 1, STEP 2,
and STEP 3 calibration as follows.
STEP1 – DETECTION/DISTANCE STEP2 – FREQUENCY STEP3 – LEVEL
For your reference
Loud test tones are output from each speaker during the configuration.
During setup, operations may stop when there is an error message on the display.
Refer below for troubleshooting.
During setup, operations may stop when there is an error message on the display.
Refer below for troubleshooting.
•
•
•
•
•
STEP 4
Auto speaker setup
To cancel during setup
Message
Solutions
Pages
“INSERT MIC”
Calibration microphone is not detected. Insert the microphone correctly.
•
11
“CHECK CONNECTION TO
LS/RS SPEAKERS”
LS/RS SPEAKERS”
One of the surround speakers is not detected. Check the connections.
•
6
“CHECK CONNECTION TO
L/R SPEAKERS”
L/R SPEAKERS”
Check the front (L) and (R) connections.
•
6
Troubleshooting for auto speaker setup
While performing auto speaker setup, errors may occur and the messages will blink or scroll on the display, depending on the
conditions. Press any button on the main unit or remote control to stop the setup.
After troubleshooting, press and hold
conditions. Press any button on the main unit or remote control to stop the setup.
After troubleshooting, press and hold
to start the setup process again.
Auto speaker setup may produce an unsatisfactory result with some speaker setups and configurations.
Auto speaker setup will not start if you have muted the speakers. Turn the muting off (➡ page 19).
Auto speaker setup will not start if you have plugged in headphone. Unplug any headphone.
VIERA Link “HDAVI Control
Auto speaker setup will not start if you have muted the speakers. Turn the muting off (➡ page 19).
Auto speaker setup will not start if you have plugged in headphone. Unplug any headphone.
VIERA Link “HDAVI Control
TM
” (➡ page 8) is disabled during auto speaker setup.
•
•
•
•
•
•
•
Note
Press any button on the main unit or remote control.
“CANCELED” appears on the display.
“COMPLETE” appears on the display and all calibrations are saved.
[AUTO SPEAKER SETUP] indicator lights.
[AUTO SPEAKER SETUP] indicator lights.
To exit, press and hold
.
Disconnect the calibration microphone.
•
•
•
•
•
•
-AUTO SETUP
AUTO
SPEAKER SETUP
AUTO
SPEAKER SETUP
Auto speaker setup finishes.
Start performing auto
speaker setup.
speaker setup.
Auto speaker setup
Perform auto speaker setup again if you have changed the speakers, speaker positions, or the layout of your listening
environment.
If you find speaker output unsatisfactory, reset all auto speaker setup settings and change them manually. Refer to “Auto setup”
(➡ page 13).
The calibration will give optimal result for “DISTANCE”. Therefore, you are unable to adjust the setting manually.
environment.
If you find speaker output unsatisfactory, reset all auto speaker setup settings and change them manually. Refer to “Auto setup”
(➡ page 13).
The calibration will give optimal result for “DISTANCE”. Therefore, you are unable to adjust the setting manually.
•
•
•
Note
Turn off all components before making any connections.
Peripheral equipment and cables sold separately
unless otherwise indicated.
To connect equipment, refer to the appropriate
operating instructions.
•
•
•
-AUTO SETUP
-AUTO SETUP
SC-HT56P_MP (RQTX0175-2P).indb 12
9/19/2008 12:28:28 PM