ONKYO 29344937 ユーザーズマニュアル
19
Connecting the AV receiver
Speaker Configuration
For 7.1-channel surround-sound playback, you need
seven speakers and a powered subwoofer.
The following table shows which channels you should
use based on the number of speakers you have.
seven speakers and a powered subwoofer.
The following table shows which channels you should
use based on the number of speakers you have.
*1 If you’re using only one surround back speaker, connect it to the
power amplifier’s left terminals.
No matter how many speakers you use, a powered
subwoofer is recommended for a powerful and solid
bass.
To get the best from your surround-sound system, you
must set the speaker settings. You can do this
automatically (see page 46) or manually (see page 68).
Notes:
• Front high and surround back speakers produce no
subwoofer is recommended for a powerful and solid
bass.
To get the best from your surround-sound system, you
must set the speaker settings. You can do this
automatically (see page 46) or manually (see page 68).
Notes:
• Front high and surround back speakers produce no
sound at the same time.
• When you connect the front high left and right
speakers, preparate it separately.
Speaker Connection Precautions
Read the following before connecting your speakers:
• North American models: You can connect speakers
• North American models: You can connect speakers
with an impedance of between 6 and 16 ohms. If you
use speakers with a lower impedance, and use the
amplifier at high volume levels for a long period of
time, the built-in amp protection circuit may be
activated.
use speakers with a lower impedance, and use the
amplifier at high volume levels for a long period of
time, the built-in amp protection circuit may be
activated.
• Asian models: You can connect speakers with an
impedance of between 4 and 16 ohms. If the
impedance of any of the connected speakers is 4 ohms
or more, but less than 6 ohms, be sure to set the
minimum speaker impedance to “4 ohms” (see
page 44). If you use speakers with a lower impedance,
and use the amplifier at high volume levels for a long
period of time, the built-in amp protection circuit may
be activated.
impedance of any of the connected speakers is 4 ohms
or more, but less than 6 ohms, be sure to set the
minimum speaker impedance to “4 ohms” (see
page 44). If you use speakers with a lower impedance,
and use the amplifier at high volume levels for a long
period of time, the built-in amp protection circuit may
be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. Connect
• Pay close attention to speaker wiring polarity. Connect
positive (+) terminals to only positive (+) terminals,
and negative (–) terminals to only negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
and negative (–) terminals to only negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
• Unnecessarily long or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
Doing so may damage the AV
receiver.
• Don’t connect more than one
cable to each speaker
terminal. Doing so may
damage the AV receiver.
terminal. Doing so may
damage the AV receiver.
• Don’t connect a speaker to several terminals.
Connecting Your Speakers
Number of speakers:
2
3
4
5
6
7
7
8
9
Front left
✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
Front right
✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
Center
✓
✓ ✓ ✓ ✓ ✓ ✓
Surround left
✓ ✓ ✓ ✓ ✓ ✓ ✓
Surround right
✓ ✓ ✓ ✓ ✓ ✓ ✓
Surround back
*1
✓
✓
Surround back left
✓
✓
Surround back right
✓
✓
Front high left
✓ ✓ ✓
Front high right
✓ ✓ ✓