Euro-Pro EP722 ユーザーズマニュアル

Hold the plug  when rewinding 

the cord.  Do not allow the cord to whip

when rewinding.

3. To rewind the power cord, 

press the cable rewind button 

with one hand and guide the 

power cord with the other hand  to 

ensure that it does not whip 

causing damage.

4. Take the HEPA dust cup filter 

out of the dust cup, do not let 

dust fall out of dust cup.

Always unplug the unit from 

electrical outlet before opening the Dust 

Cup (container).

1.

Crevice Tool
For radiators, crevices,

corners, baseboards and 

between cushions.

Do NOT use the HEPA filter 

cartridge without the debris screen in 

place.

2.

Dusting Brush
The dusting brush is used for 

the furniture, venetian blinds, 

books, lamp shades and 

shelves.

3.

Upholstery Brush
The dusting brush is used 

for the furniture.

After each Use - Always 

remove the Filter Debris Screen from the 

HEPA  Dust Cup Filter, then vigorously 

“TapClean” HEPA Filter until no more 

dust can be removed.

5. Take the dust cup and dispose 

of the dust inside.

IMPORTANT, Please Note : The 

“TapClean” HEPA Dust Cup Filter & 

Debris Screen will stop most of the tiniest 

dust particles and airborne allergens from 

re-entering the air you breathe. In fact it 

stops 99.97% of all particles as small as 

0.3 microns - many times smaller than a 

human hair!!! Because of this incredible 

filtration performance, the HEPA Dust Cup 

Filter will quickly accumulate, inside the 

white filter folds, many fine dust particles 

that are difficult to see but which will 

eventually block or reduce your suction 

power - if not cleaned properly. This can 

cause the motor to overheat and the re-

settable thermostat to trip. (Should this 

happen turn off the switch, unplug the unit 

and allow unit to cool down. Clean the 

HEPA Filter and Debris Screen as 

described in this section, then reconnect 

unit and proceed with vacuuming.)

HEPA Filter

Debris Screen

7. Vigorously “TapClean” 

the HEPA Dust 

Cup Filter on a

hard surface until no 

more dust is observed 

falling out from 

between the pleats of 

the filter. Please note 

that on the under side of the HEPA 

dust cup filter there is a small brush 

which you can use to brush out the 

pleats of the filter.

6. Separate the debris screen from the 

HEPA filter cartridge by grasping the 

debris screen with one hand and the 

filter frame with the other and pull 

apart. 

To reduce the risk of electric 

shock, the power cord must be 

disconnected before removing the dust 

cup, dust cup filter,changing the filters or 

performing maintenance/trouble shooting 

checks.

Your vacuum cleaner includes a power 

cord, which is automatically retractable.  

To extend your power cord, pull from 

rear and extend to desired length.  

When cleaning is finished, first switch 

off power and disconnect plug from 

electrical outlet.  Then press on cord 

rewind button.  If the cord does not fully 

retract, pull it out again and then press 

on cord rewind button.

Before using the appliance, 

unwind a sufficient length of cable and 

Insert the plug into the wall socket.  A 

yellow mark on the power cord shows the 

ideal cable length.  Don’t pull the power 

cord beyond the red mark. 

1. Slide locking latch forward then tilt the 

top housing of the brush upwards. The 

top housing is hinged and will tilt up 

approximately 45° only.

2. Inspect turbine wheel and air passage 

for debris and/or blockage. Remove 

debris if present.

3. Inspect the rotating brush for built-up 

hair or string. If present, remove by 

carefully cutting with scissors. Avoid 

damaging or cutting bristles.

4. Once clean, close the top cover of the 

turbo brush and slide the locking latch 

toward the rear of the brush to lock.

1. Push the Power On/Off switch 

to the OFF position to 

disconnect the power.

2. Remove the flexible hose.

3. Remove the dust cup by lifting 

the dust cup handle. See 

illustration below.

1. Insert the power plug into the wall 

outlet.

2. Press the Power On/Off Switch to 

activate the vacuum cleaner.

8. “TapClean” the Debris 

Screen or rinse under 

a faucet until clean. 

Remember that 

the Debris Screen 

must be completely 

dry before reinstalling 

in the vacuum.

6

5