Ridgid WD1230 ユーザーズマニュアル
9
Operation (continued)
Vacuuming Liquids
1.When picking up small amounts of liquid
the filter may be left in place.
2.When picking up large amounts of liquid
we recommend that the filter be
removed. If the filter is not removed, it
will become saturated and misting may
appear in the exhaust.
removed. If the filter is not removed, it
will become saturated and misting may
appear in the exhaust.
3.After using the vac to pick up liquids, the
filter must be dried to avoid possible
mildew and damage to the filter.
mildew and damage to the filter.
4.When the liquid in the drum reaches a
predetermined level, the float mecha-
nism will rise automatically to cut off air-
flow. When this happens, turn off the
vac, unplug the power cord, and empty
the drum. You will know that the float
has risen because vac airflow ceases
and the motor noise will become higher
in pitch, due to increased motor speed.
nism will rise automatically to cut off air-
flow. When this happens, turn off the
vac, unplug the power cord, and empty
the drum. You will know that the float
has risen because vac airflow ceases
and the motor noise will become higher
in pitch, due to increased motor speed.
IMPORTANT: To avoid damage to the
vac do not run motor with float in raised
position.
vac do not run motor with float in raised
position.
Emptying the Drum
WARNING: To reduce the risk of
injury from accidental starting,
unplug power cord before emptying
the drum.
injury from accidental starting,
unplug power cord before emptying
the drum.
l. The vac comes equipped with a drain
for easy emptying of liquids. Simply
unscrew the drain cap and lift the oppo-
site side slightly to empty the drum.
unscrew the drain cap and lift the oppo-
site side slightly to empty the drum.
2. Another option is to remove the lid. Pull
the flexible latches outward on each
side of the lid to release from the drum.
side of the lid to release from the drum.
3. While holding the latches out, lift the top
assembly up and away from the drum.
4. Lay top assembly upside down on a
clean area while emptying drum or
changing filter.
changing filter.
5. Dump the drum contents into the proper
waste disposal container.
WARNING: To reduce the risk of
back injury or falls, do not lift a vac
heavy with liquid or debris. Scoop
or drain enough contents out to
make the vac light enough to lift
comfortably.
back injury or falls, do not lift a vac
heavy with liquid or debris. Scoop
or drain enough contents out to
make the vac light enough to lift
comfortably.
Moving the Vac
1. Should it become necessary to pick the
vac up to move it, DO NOT pick the vac
up by the lid handles unless dust drum
is empty. To avoid dropping the vac due
to latches releasing or possible part
breakage, pick the vac up by the lip of
the dust drum.
up by the lid handles unless dust drum
is empty. To avoid dropping the vac due
to latches releasing or possible part
breakage, pick the vac up by the lip of
the dust drum.
Blowing Feature
Your vac features “Full Blowing”. It can
blow sawdust and other debris. Follow the
steps below to use your vac as a blower.
blow sawdust and other debris. Follow the
steps below to use your vac as a blower.
WARNING: Always wear safety gog-
gles complying with ANSI Z87.1 (or
in Canada CSA Z94-3-99) before
using as a blower.
gles complying with ANSI Z87.1 (or
in Canada CSA Z94-3-99) before
using as a blower.
WARNING: To reduce the risk of
injury to bystanders, keep them
clear of blowing debris.
injury to bystanders, keep them
clear of blowing debris.
1. Locate blowing port of your vac.
2. Insert soft end of your hose into blowing port.
3. (Optional) Attach extension wand to
2. Insert soft end of your hose into blowing port.
3. (Optional) Attach extension wand to
swivel end of hose.
4. Turn vac on and you are ready to use
your vac as a blower.
5. (Optional) for enhanced blowing
performance purchase accessory blower
nozzle VT2506.
performance purchase accessory blower
nozzle VT2506.
Soft End
Swivel End
of Hose
of Hose
WD1200/30 RIDGID MANUAL (12001 3/16/01 4:23 PM Page 9