Linear wt00z-1 ユーザーズマニュアル
1
NOTE: This module must be “included in the Network” only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this module.
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this module.
WTOOZ-1 WALL MOUNTED TRANSMITTER
Linear’s family of Z-Wave certifi ed wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent
wireless capability to commercial and residential environments.
dimmers, outlets and plug-in modules) brings a new level of intelligent
wireless capability to commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard
for remote home automation, security and other applications.
Embedded in each device, the Z-Wave smart chip enables two-way RF
communication among hundreds of Z-Wave enabled devices, allowing
products and services from multiple manufacturers to work seamlessly.
for remote home automation, security and other applications.
Embedded in each device, the Z-Wave smart chip enables two-way RF
communication among hundreds of Z-Wave enabled devices, allowing
products and services from multiple manufacturers to work seamlessly.
Linear Z-Wave products are easy to install, and allow dealers to create
an integrated wireless network with nearly limitless expansion and
interoperability with security and health monitoring systems, energy
management, home entertainment, appliances, and more.
an integrated wireless network with nearly limitless expansion and
interoperability with security and health monitoring systems, energy
management, home entertainment, appliances, and more.
INSTALLATION
DANGER! SHOCK HAZARD. Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the
United States, or the Canadian Electrical Code and local regulations
in Canada. It is recommended that a qualifi ed electrician perform this
installation. Retain instructions for future use. With power off, wire this
WT00Z-1 according to the diagram shown above. If more than one
WT00Z-1 is to be installed in a wall box, scored tabs on the side can
be broken off by bending back and forth with pliers, to accommodate
proper fi t. Apply power when completed. Refer to your Controller
operating instructions on how to include this module in the RF network
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the
United States, or the Canadian Electrical Code and local regulations
in Canada. It is recommended that a qualifi ed electrician perform this
installation. Retain instructions for future use. With power off, wire this
WT00Z-1 according to the diagram shown above. If more than one
WT00Z-1 is to be installed in a wall box, scored tabs on the side can
be broken off by bending back and forth with pliers, to accommodate
proper fi t. Apply power when completed. Refer to your Controller
operating instructions on how to include this module in the RF network
INCLUDING WT00Z-1 TO THE NETWORK
STEP 1. Prepare the Controller to include a unit to the network by
adding it to a group (method of adding a node to the network). Refer
to controller instructions.
adding it to a group (method of adding a node to the network). Refer
to controller instructions.
STEP 2. The WT00Z-1 must be in its permanently installed
location. Tap either the top or bottom of the WT00Z-1 once.
location. Tap either the top or bottom of the WT00Z-1 once.
STEP 3. You should see an indication on your Controller that the
“device was included” in the network.
“device was included” in the network.
NOTE: If you have trouble adding the WT00Z-1 to a group it may be
that the Home ID and Node ID were not cleared from it after testing.
You must fi rst “RESET UNIT” with your controller to remove it from
the network. Although adding it to a group includes it in the network,
removing it from a group does not remove it from the network. If
removed from a group, it functions as a repeater (only). “RESET UNIT”
removes it completely from the network.
that the Home ID and Node ID were not cleared from it after testing.
You must fi rst “RESET UNIT” with your controller to remove it from
the network. Although adding it to a group includes it in the network,
removing it from a group does not remove it from the network. If
removed from a group, it functions as a repeater (only). “RESET UNIT”
removes it completely from the network.
WT00Z-1
Radio Frequency (RF) Controlled, 120 VAC, Wall Mounted
Transmitter, Series 300
SUPPLIED WITH DECORATIVE SWITCH PLATE
NEUTRAL
120 VAC
PUSH ON (PUSH
& HOLD TO BRIGHTEN)
& HOLD TO BRIGHTEN)
WHITE
LINE
BLACK
PUSH OFF
(PUSH AND
HOLD TO DIM)
(PUSH AND
HOLD TO DIM)
STATUS LED
GREEN GROUND
PUSH TOP OR
BOTTOM OF PADDLE
SWITCH ONCE TO
INCLUDE IN NETWORK
BOTTOM OF PADDLE
SWITCH ONCE TO
INCLUDE IN NETWORK
TO MOUNT MORE THAN ONE
WT00Z-1IN A BOX, SCORED TAB
WILL BREAK FLUSH WITH EDGE
OF PLASTIC
WT00Z-1IN A BOX, SCORED TAB
WILL BREAK FLUSH WITH EDGE
OF PLASTIC