Xantech 172-77 ユーザーズマニュアル
IR Receivers
3
172-77
INSTALLING THE XTRA LINK 284M DUAL IR EMITTER
Plug the 284M Dual IR Emitter into the jack marked "EMITTER" on the CPL77 Coupler in the Main Room.
The 284M emitters should be installed directly to the infrared sensor "window" on the front panel of the
satellite receiver, VCR, cable box, etc. Simply remove the paper backing exposing the adhesive surface
of each emitter and apply them to the center of the sensor window.
satellite receiver, VCR, cable box, etc. Simply remove the paper backing exposing the adhesive surface
of each emitter and apply them to the center of the sensor window.
NOTE: Although the 284M appears dark to the eye, it is transparent to infrared. Positioning the 284M
directly over the infrared window(s) of the component(s) will not block direct IR control from a handheld
remote.
directly over the infrared window(s) of the component(s) will not block direct IR control from a handheld
remote.
OPERATION
To use the Xtra Link Remote Control Extension System, simply point your handheld remote control(s) at
the 291-00 IR Receiver and press the desired button. A red LED on the front of the 291-00 will indicate the
reception of your infrared command.
the 291-00 IR Receiver and press the desired button. A red LED on the front of the 291-00 will indicate the
reception of your infrared command.
NOTE: The maximum usable distance between your IR remote and the 291-00 Receiver will vary for each
remote and might be shorter than when directly used in the room containing the satellite receiver or other
IR controlled devices.
remote and might be shorter than when directly used in the room containing the satellite receiver or other
IR controlled devices.
ADVANCED MULTIROOM HOOKUP
Fig. 3 shows an advanced system using two Xtra Links in a multiroom installation. Except for the addition
of a 2-way DC passing RF splitter (such as Xantech part no. 04027500), the connections are essentially
the same.
of a 2-way DC passing RF splitter (such as Xantech part no. 04027500), the connections are essentially
the same.
TO
T
V
Satellite Dish
TV SIGNAL PATH
IR REMOTE CONTROL PATH
IR REMOTE CONTROL PATH
Hand Held
Remote
REMOTE
ROOM
RF
IN
284M
Dual Mouse
Emitter Assembly
(included)
MAIN ROOM
CPL77 COUPLER
(included)
Room-to-Room Coaxial Cable
(not included)
Coaxial Cable
(not included)
Place emitters on
the IR sensor
window on front
panel of each
controlled unit.
the IR sensor
window on front
panel of each
controlled unit.
Emitter
RF IN
OUT TO TV
SATELLITE
RECEIVER
RECEIVER
(Back Panel)
RF IN
VCR
(Back Panel)
Emitter
IR Sensor Windows
(Front Panel)
Coaxial Cable
(not included)
To 220 V AC
(unswitched)
291-00
IR RECEIVER
(included)
2ND
TV
1ST
TV
RF IN
Coaxial Cable
(not included)
REMOTE
TV
EMITTER
LOCAL TV
CPL77 COUPLER
SA
T/VCR
Front View
Side View
OUT TO TV
IR RECEIVER
INJ77 INJECTOR
ANT INPUT
+12 V
Front View
Side View
RF SPLITTER
2-Way DC Passing
(Xantech # 04027500,
not Included)
Room-to-Room
Coaxial Cable
(not included)
TO
T
V
REMOTE
ROOM
RF
IN
To 220 V AC
(unswitched)
INJ77
INJECTOR
(included)
3RD
TV
781C77
Power Supply (included)
IR RECEIVER
INJ77 INJECTOR
ANT INPUT
+12 V
Front View
Side View
Coaxial Cable
(not included)
Hand Held
Remote
291-00
IR RECEIVER
(included)
781C77
Power Supply (included)
INJ77
INJECTOR
(included)
Fig. 3 Advanced Multiroom Hookup