Radio Shack 3-DVD Changer ユーザーズマニュアル

DVD Player Operation

5. Press

DVD SET UP

to exit.

Notes:

• Some titles do not match with the rating level described as

above.

• If you change the level and enter a password, playback of all

DVDs with ratings higher than your selection will be blocked,
unless you enter the correct password again. For example: if you
change the level to 5, the DVD player will not play discs with rat-
ings of 6, 7, or 8 unless the correct password is entered from the
remote control.

Setting a Password

If you change the rating level to 7 or lower, you must enter a 4-digit
password to access playback of discs with higher ratings.

To set this password, follow these steps.

1. Press

DVD SET UP

2. At the setup screen, press

to select

F7IIMEH:

, then press

ENTER

3. Type a 4-digit password into

EB:

. (For example, 1234).

Important: Do not forget your password.

4. Type same the 4-digit password into

D;M

, then press

ENTER

Clearing Your Password

If you forget your password, you can clear the current password.

At the SETUP screen, press

to select

F7IIMEH:

, then press

EN-

TER

Enter 4-digit number (for example, 2850), then press

ENTER

. The 4-

digit password is cleared.

SELECTING TV ASPECT

Select the appropriate screen type according to your TV set. Conven-
tional size screens use a 4:3 aspect ratio, and wide-screens use a
16:9 ratio.

1. Press

DVD SET UP

2. At the setup screen, press

to select

JLý:?IFB7O

, then

press

ENTER

3. Repeatedly press

ENTER

to select the desired aspect, then press

DVD SET UP

. You must select the type of TV picture (aspect ratio)

that corresponds to the type of TV you are connecting to the
DVD unit.

*0)ýFI

(Pan & Scan) — If you have a conventional TV set and

your DVD is not formatted for widescreen viewing, use this set-
ting.

*0)ýB8

(Letterbox) — If you have a conventional TV set and your

DVD is formatted for widescreen viewing, use this setting. All
video material not formatted in the Pan & Scan style is played
back in the letterbox style. Black bands appear at top and bottom
of screen.

',0/ýM?:;

(Widescreen) — If you have a wide-screen TV set, use

this setting. The DVD plays in full size. (You must also set your
widescreen TV to “full size”).

SELECTING DIGITAL AUDIO OUT

Each DVD has a variety of audio output options. If you connected a
device to the receiver’s digital optical jacks (see “Connecting a Digital
Optical Audio Devices” on Page 7), you might have to change the
digital audio output setting. Set the player’s Digital Audio Output ac-
cording to the type of audio system you use.

1. Press

DVD SET UP

2. At the setup screen, press

to select

:?=?J7BýEKJ

3. Repeatedly press

ENTER

to select the desired output (

F9C

8?JIJH;7C

) , then press

ENTER

8?JIJH;7C

— Select

8?JIJH;7C

if you have an amplifier or other

equipment with DTS decoder or Dolby Digital decoder connected
to the receiver.

F9C

— Select

F9C

if you have an amplifier or other equipment

with linear PCM only (or a MD recorder or a DAT deck) con-
nected to the receiver.

Caution: If an active digital audio output signal is supplied to an re-
ceiver or other equipment without a corresponding digital decoding
capability, a very loud noise may be produced which could perma-
nently damage the speakers.

Note: When you make a digital recording from CD to your house au-
dio CD recorder entire CD tracks are recorded as 1 track. This is be-
cause there is no track information.