Arcam CD73 ユーザーズマニュアル

CD73

CD73

En

gl

is

h

Using the CR224 remote control

Turns the display on or off. Turning the display off 

generally produces a slight improvement in sound 

quality. 

A–B 
This button enables you to repeat any section of 
music within a track. Whilst the disc is playing, press 
the 

 button at the start of the section you wish 

to repeat. ‘REPEAT’ is shown on the display and the 
letter ‘A–’ flashes. Press the button a second time 
when you reach the end of the section you wish to 
repeat. The ‘A–B’ letters stop flashing and remain 
lit. This section will repeat until you press   or 

 or 

 . The forward search button (

) moves forward 

within the selected loop.

REPEAT
To repeat the entire CD or a pre-programmed 
selection of tracks press 

 once: ‘REPEAT’ 

lights on the display. To repeat a particular track, 
select that track and then press 

 twice so 

that ‘REPEAT 1’ is shown on the display. If you now 
select a different track, that track is repeated 
instead.
To cancel the repeat function press 

 a third 

time.

Press 

 once to display the remaining time of the 

currently playing track. Press again to display the 

time remaining on the disc. Press a third time to turn 

the text display on. 

Press 

 again and the display reverts to its 

original setting, showing the time elapsed for the 

current track.

For CDs with text, pressing 

 once while the disc 

is loaded but not playing displays the artist’s name.

Pressing 

 a second time displays the total 

number of tracks and the total playing time.

0–9 keypad
This allows direct access to individual tracks on 
the disc. To select a track, press the corresponding 
keypad button. For tracks greater than 9, enter the 
digits in sequence. For example, to play track 15, 
press and hold 

 until the number on the display 

moves to the left, then press 

.

PROG (Program) 

You can program a selection of up to 24 tracks 

from a disc to play in any order. Select a track by 
using the 

 and 

 buttons, then press 

 to 

program the track into memory (‘PROGRAM’ appears 

on the display to indicate that you have started 

programming a sequence). Repeat these steps to 

program the remaining tracks in your selection. 

Alternatively, press 

 once and enter your track 

selection using the 0–9 keypad.

The display shows the track numbers programmed, 

the total length of the programmed sequence and 

the number of tracks programmed (shown by a 

number below the word ‘STEP’). 

Each time you enter a track the number below ‘STEP’ 

increments by one and flashes until you press 

 

to confirm. If you fail to press 

 within about five 

seconds the display stops flashing and you will have 

to reselect the track.

Press 

to play the program. Press   again to replay 

the entire sequence from the start. Press 

 

again to exit the program facility: the display flashes 

‘CONTINUE’ and shows ‘0’.

MUTE 
Stops sound to the speaker outputs of certain Arcam 
amplifiers.

VOL (Volume) +/– 
Adjusts the volume on Arcam remote-controllable 
amplifiers.
Note that the volume (+/–) controls and 

 

button have no effect on the audio output level of the 
CD players.

NOTE: Remember to install the two AAA batteries 
supplied before trying to use your remote control.
Do not place anything in front of the display area 
on the CD player (where the IR receiver is located), 
or the remote control may not work.

Opens and closes the CD tray.

Skip track backwards and forwards; search 

backwards and forwards (see page 5)

Playback control
Play, Stop and Pause (see page 5).

SHUFFLE
Press once to shuffle play CD tracks (i.e. play them 
in a random order). Press again to cancel shuffle 
play.

These operate in the same way as the source 

selector on the front panel of an Arcam integrated 

amplifier.