Princeton 4411-0097 ユーザーズマニュアル
16
PI-MTE System Manual
Version 4.C
#
Feature
#
Feature
8
TTL In/Out: User-programmable
interface with eight input bits and eight
output bits that can be written to or
polled for additional control or
functionality. Refer to "
interface with eight input bits and eight
output bits that can be written to or
polled for additional control or
functionality. Refer to "
TTL Control
",
page 58.
15
Fuse/Voltage Label: Displays the
controller’s power and fuse requirements.
This label may appear below the power
module.
controller’s power and fuse requirements.
This label may appear below the power
module.
9
AUX Output: Reserved for future use.
16
USB 2.0 Connector: Provides two-way
serial communication between the controller
and the host computer. Uses USB 2.0
protocol.
serial communication between the controller
and the host computer. Uses USB 2.0
protocol.
Cables
Vacuum-Compatible Camera-Vacuum Cable: This 1-meter cable has
DB-25 connectors that interconnect the DB-25 connector on the back of the camera
and a 25-pin D connector on a compatible vacuum flange. Available in Kapton
DB-25 connectors that interconnect the DB-25 connector on the back of the camera
and a 25-pin D connector on a compatible vacuum flange. Available in Kapton
®
flat cable (6050-0467) or in low vacuum cable with braided sleeve (6050-0475).
The low vacuum cable is also available in 1.5 meter and 2 meter lengths.
The low vacuum cable is also available in 1.5 meter and 2 meter lengths.
Detector-Controller: (6050-0526) 50 kHz/2 MHz systems: The standard 3'
cable has DB-25 connectors (one with slide-latch locking hardware to secure at the
controller and the other with screws for securing to a vacuum flange). This cable
interconnects the Detector connector on the rear of the ST-133 and the DB-25
connector on a compatible vacuum flange.
cable has DB-25 connectors (one with slide-latch locking hardware to secure at the
controller and the other with screws for securing to a vacuum flange). This cable
interconnects the Detector connector on the rear of the ST-133 and the DB-25
connector on a compatible vacuum flange.
Detector-Controller: (6050-0483) 100 kHz/1 MHz systems: The standard 6'
cable has DB-25 connectors (one with slide-latch locking hardware to secure at the
controller and the other with screws for securing to a vacuum flange). This cable
interconnects the Detector connector on the rear of the ST-133 and the DB-25
connector on a compatible vacuum flange.
cable has DB-25 connectors (one with slide-latch locking hardware to secure at the
controller and the other with screws for securing to a vacuum flange). This cable
interconnects the Detector connector on the rear of the ST-133 and the DB-25
connector on a compatible vacuum flange.
Note: If the PI-MTE camera is being operated out-of-vacuum (i.e., with the visible
nose, containing a quartz window, mounted to the front of the camera for operation in a
non-vacuum environment), an optional 10' cable (6050-0321), with slide latches at both
ends, is available to directly interconnect the PI-MTE camera and the ST-133. Detector-
Controller. Cables 15' and 20' long are also available for out-of-vacuum operation.
nose, containing a quartz window, mounted to the front of the camera for operation in a
non-vacuum environment), an optional 10' cable (6050-0321), with slide latches at both
ends, is available to directly interconnect the PI-MTE camera and the ST-133. Detector-
Controller. Cables 15' and 20' long are also available for out-of-vacuum operation.
Interface Cable: Depending on the system configuration, either a USB or a TAXI
cable will be shipped.
cable will be shipped.
TAXI: The standard 25' (7.6 m) cable (6050-0148-CE) has DB-9 Male
connectors with screw-down locking hardware. The TAXI (Serial
communication) cable interconnects the "Serial Com" connector on the rear of the
ST-133 with the Princeton Instruments (RSPI) high speed PCI card installed in the
host computer. In addition to the standard length, this cable is available in 10', 50',
100', and 165' lengths. Also available are fiber optic adapters with fiber optic
cables in 100, 300, and 1000 meter lengths.
connectors with screw-down locking hardware. The TAXI (Serial
communication) cable interconnects the "Serial Com" connector on the rear of the
ST-133 with the Princeton Instruments (RSPI) high speed PCI card installed in the
host computer. In addition to the standard length, this cable is available in 10', 50',
100', and 165' lengths. Also available are fiber optic adapters with fiber optic
cables in 100, 300, and 1000 meter lengths.
USB 2.0: The standard 16.4' (5 m) cable (6050-0494) has USB connectors
that interconnect the "USB 2.0" connector on the rear of the ST-133 with a
USB card installed in the host computer.
that interconnect the "USB 2.0" connector on the rear of the ST-133 with a
USB card installed in the host computer.