Tascam DA-302 ユーザーズマニュアル
17
Section 5 : Recording
Dual recording means recording the same input source on
both Deck 1 and Deck 2.
both Deck 1 and Deck 2.
1
Connect the input source to the ANALOG IN connec-
tors if it is analog and to the DIGITAL IN "1" connec-
tor if it is digital.
·Connecting it to the DIGITAL "2" connector is
tors if it is analog and to the DIGITAL IN "1" connec-
tor if it is digital.
·Connecting it to the DIGITAL "2" connector is
invalid.
2
Set the COMMON MODE switch to "1&2".
3
For analog input signals, follow procedures 3 to 6 in
"5-1-1. Recording analog input signals". For digital
input signals, set the INPUT switch to DIGITAL.
"5-1-1. Recording analog input signals". For digital
input signals, set the INPUT switch to DIGITAL.
4
When Deck 1 is set in the Record mode, recording
starts on both Deck 1 and Deck 2 simultaneously.
starts on both Deck 1 and Deck 2 simultaneously.
5
When the Stop key on Deck 1 is pressed, recording on
both Deck 1 and Deck 2 stops simultaneously.
both Deck 1 and Deck 2 stops simultaneously.
… When the COMMON MODE switch is set to "1&2", the
STOP key, PLAY key, PAUSE key, RECORD key, F
FWD key, REW key and REC MUTE key on Deck 1
(Deck 2) are effective for both decks.
FWD key, REW key and REC MUTE key on Deck 1
(Deck 2) are effective for both decks.
… The input signals during recording are output from the
ANALOG OUT connectors and the DIGITAL OUT
connector of Deck 1 and Deck 2.
connector of Deck 1 and Deck 2.
5-3. Dual recording
Continuous recording means recording one input source
continuously using tapes in Deck 1 and Deck 2.
continuously using tapes in Deck 1 and Deck 2.
1
Connect the input source to the ANALOG IN connec-
tors for analog input signals and to the DIGITAL IN
"1" connector for digital signals.
·The DIGITAL IN "2" connector is disabled.
tors for analog input signals and to the DIGITAL IN
"1" connector for digital signals.
·The DIGITAL IN "2" connector is disabled.
2
Set the COMMON MODE switch to "1
> 2".
3
For analog input signals, follow procedures 3 to 6 in
"5-1-1. Recording analog input signals". For digital
input signals, set the INPUT switch to DIGITAL.
"5-1-1. Recording analog input signals". For digital
input signals, set the INPUT switch to DIGITAL.
4
Set "Seqtime" in the menu. (
úp.28)
5
Set Deck 1 in the Record mode and start recording.
When the ABS time of Deck 1 reaches the time set
with "Seqtime", Deck 2 automatically starts recording.
When the ABS time of Deck 1 reaches the time set
with "Seqtime", Deck 2 automatically starts recording.
6
Deck 1 rewinds the tape automatically to the beginning
either 3 minutes after the time set with ''Seqtime'' or
when the tape end is reached.
either 3 minutes after the time set with ''Seqtime'' or
when the tape end is reached.
7
Deck 2 rewinds the tape automatically to the beginning
either 3 minutes after the time set with ''Seqtime'' or
when the tape end is reached.
either 3 minutes after the time set with ''Seqtime'' or
when the tape end is reached.
… To stop recording in the middle, press the STOP key on
the deck which is recording.
… The input signals being recorded are output from the
ANALOG OUT connectors and DIGITAL OUT con-
nector of Deck 1 (Deck 2).
nector of Deck 1 (Deck 2).
5-4. Continuous recording