Tascam DA-45HR オーナーマニュアル
3 - Menu functions
20
TASCAM DA-45HR
3.11HR time display
When recording or playing back in the
HR(24BIT)
mode, the tape moves at twice the normal speed. The
tape counter can use the subcode recorded on the
tape as its reference, meaning that the displayed time
passes twice as fast as real time, or it can display real
time.
tape counter can use the subcode recorded on the
tape as its reference, meaning that the displayed time
passes twice as fast as real time, or it can display real
time.
The selected display mode is used in PGM Time
mode and REMAIN Time mode (see
mode and REMAIN Time mode (see
COUNTER
MODE [21]
). A * symbol appears at the top of the
display when real time mode is selected.
The options available in this menu are:
TapeTM
(using the ABS time in the tape subcode), or
RealTM
(using real time for the tape counter).
The default value is
TapeTM
.
NOTE
This menu item only applies to tapes
recorded in the HR mode; it has no relevance
to tapes recorded in standard mode.
recorded in the HR mode; it has no relevance
to tapes recorded in standard mode.
3.12Repeat mode
This menu item controls the number of times that the
playback will repeat when the repeat mode is set (see
4.1, "REPEAT").
playback will repeat when the repeat mode is set (see
4.1, "REPEAT").
The options available are:
10TMS
(the playback
will repeat 10 times) and
UnLimt
(the playback
will repeat indefinitely until stopped).
The default value is
10TMS
.
3.13Pre-roll time
Sets a pre-roll time, so that the tape will locate to a
fixed point before either of the location memories
when the appropriate key (
fixed point before either of the location memories
when the appropriate key (
LOC 1 [29]
or
LOC 2
[30]
) is pressed. The setting made here has no effect
on locating to the START IDs of programs using the
SKIP
keys
[12]
or the
DATA
dial
[20]
.
The values available are:
0
,
1
,
2
,
3
,
4
and
5
seconds.
The default value is
0
seconds.
3.14End tally signal
Controls the timing of the tape end tally signal trans-
mitted through the
mitted through the
CONTROL I/O [36]
port. The
signal can either be transmitted at the end of the tape,
or at a fixed interval before the tape end.
or at a fixed interval before the tape end.
The values available are:
T-End
(the tally signal
will be transmitted at the end of the tape),
1min
,
2min
and
3min
(the tally signal will be trans-
mitted before the end of the tape is reached).
The default value is
T-End
.
3.15Auto rewind
This menu item determines whether the tape will be
automatically rewound when the end of the tape or
an END ID is reached in play mode.
automatically rewound when the end of the tape or
an END ID is reached in play mode.
The two options available are:
off
(the tape will
not be rewound when the end of the tape or an END
ID is reached) and
ID is reached) and
on
(the tape will be automati-
cally rewound when the end of the tape or an END
ID is reached).
ID is reached).
The default value is
off
.
3.16Fast forward mode
This menu item determines whether the F FWD and
REW keys will act as cue and review keys, respec-
tively, if they are pressed while the tape deck is in
play mode. The two settings are
REW keys will act as cue and review keys, respec-
tively, if they are pressed while the tape deck is in
play mode. The two settings are
Normal
(the
unit will go from play mode to fast wind) and
Cue
(the unit will enter cue/review mode when the fast
wind keys are pressed).
wind keys are pressed).
The setting made here also applies to fast wind com-
mands made through the
mands made through the
CONTROL I/O [36]
con-
nector, and using the optional RC-D45 remote
control unit.
control unit.
The default value is
Normal
.
H
R
-
T
M
T
a
p
e
T
M
R
e
p
e
a
t
1
0
T
M
S
P
r
e
R
o
l
0
s
e
c
E
n
d
T
L
Y
T
-
E
n
d
A
t
-
R
e
w
o
f
f
F
F
-
K
e
y
N
o
r
m
a l