Yamaha HTR-5140RDS ユーザーズマニュアル
56
SETUP CODES
To control your components
(MD recorder, DVD player,
TV, etc.)
(MD recorder, DVD player,
TV, etc.)
1.
Turn on the component to be used.
2.
Press the component selector which
matches the component to be
controlled (TAPE/MD, DVD/LD, TV
etc.).
matches the component to be
controlled (TAPE/MD, DVD/LD, TV
etc.).
3.
Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
flashes twice.
4.
Use the numeric buttons to enter the
four-digit manufacturer’s code for
the component to be used. Make
sure that the indicator flashes twice.
If the indicator does not flash, repeat
step 3 and re-enter the code.
four-digit manufacturer’s code for
the component to be used. Make
sure that the indicator flashes twice.
If the indicator does not flash, repeat
step 3 and re-enter the code.
5.
Press POWER (or any other button)
on the remote control transmitter to
check if you have preset the code
correctly. If the component cannot
be controlled by the remote control
transmitter, try entering another
code for the same manufacturer.
on the remote control transmitter to
check if you have preset the code
correctly. If the component cannot
be controlled by the remote control
transmitter, try entering another
code for the same manufacturer.
Returning to the factory-set
codes
codes
To return all components to the factory-
set codes, follow these steps.
1.
set codes, follow these steps.
1.
Press a button on the component
selector other than AMP<TUNER>.
selector other than AMP<TUNER>.
2.
Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
flashes twice.
3.
Enter the code number “9990”.
4.
Make sure that the indicator flashes
twice.
twice.
To return each component to the factory-
set codes, follow these steps.
1.
set codes, follow these steps.
1.
Press the component selector which
matches the component to be
returned to the factory-set codes.
matches the component to be
returned to the factory-set codes.
2.
Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
flashes twice.
3.
Enter the code number “0000”.
4.
Make sure that the indicator flashes
twice.
twice.
The following codes are preset by the
factory.
factory.
Factory-set codes
Component
Component Code
selector
TV
TV
0101
CBL/DBS
DBS tuner
0006
VCR
VCR
0002
DVD/LD
DVD player 0008 YAMAHA
CD
CD player
0005 YAMAHA
TAPE/MD
Tape deck
0004 YAMAHA
We recommend that you write all code
numbers you have preset on the “Quick
Reference Card”.
numbers you have preset on the “Quick
Reference Card”.
Presetting the remote control transmitter
Perform the presetting procedure for each component you want to control with the remote control transmitter.
Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control
Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control
transmitter that was supplied with the component.
To use a second (and third) VCR
You can control a second (and/or third)
VCR in the CBL/DBS and DVD MENU
modes if a CBL (or DBS) or DVD player
is not being used.
VCR in the CBL/DBS and DVD MENU
modes if a CBL (or DBS) or DVD player
is not being used.
If you want to control a second (and/or
third) VCR in the DVD MENU mode, you
must preset the code for an LD player in
that mode.
third) VCR in the DVD MENU mode, you
must preset the code for an LD player in
that mode.
1.
Turn on the VCR to be used.
2.
Press CBL/DBS or DVD MENU on
the component selector.
the component selector.
3.
Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
flashes twice.
4.
Use the numeric buttons to enter the
four-digit code for the second (or
third) VCR. Make sure that the
indicator flashes twice. If the
indicator does not flash, repeat step
3 and re-enter the code.
four-digit code for the second (or
third) VCR. Make sure that the
indicator flashes twice. If the
indicator does not flash, repeat step
3 and re-enter the code.
5.
Press POWER (or any other button)
on the remote control transmitter to
check if you have preset the code
correctly. If the VCR cannot be
controlled by the remote control
transmitter, try entering another
code for the same manufacturer.
on the remote control transmitter to
check if you have preset the code
correctly. If the VCR cannot be
controlled by the remote control
transmitter, try entering another
code for the same manufacturer.
01RX-V495RDS-6
6/22/99, 12:29 PM
56