Integra DTR-10.5 ユーザーズマニュアル

ページ / 152
 
11
 
Before Using the DTR-10.5
 
—Continued
 
The option boards should be installed in their individual 
designated slots. Installing the option board a different 
slot may cause failure.
 
Installing the Option Boards
 
1
 
Turn off the power and unplug the power 
cord both from the DTR-10.5 and electrical 
outlet.
 
Be sure to turn off the power of the DTR-10.5. 
Inserting or removing an option board with the 
DTR-10.5 turned on may cause failure.
 
2
 
Take the option board out from the pack-
age carefully.
 
The option board incorporates many components, 
terminals and connectors along with solderings 
on its surface. Touching the board with your fin-
gers may cause failure or damage from static elec-
tricity, incorrect contact and so on. When 
handling the board, be sure to hold the outer part 
or panel section of the board without touching the 
board surface.
 
3
 
Check the alphabet letter on the option 
board.
 
The alphabet letter is printed at the top left corner 
of the panel section.
 
4
 
Remove the sub-panel with the same 
alphabet letter as your option board from 
the back of the DTR-10.5.
 
Use the supplied Allen wrench to loosen the screw 
gradually, while holding the sub-panel so that the 
panel will not drop down.
Net
-Tune
 
is
 a
 tradem
ark
 of
 
Onkyo
 Corporation.
ETHERNET
(
Net
-Tune
)
B
Board 
surface
“Net-Tun
e” 
is a tradem
ark of 
Onkyo
 Corpo
ration.
ETHER
NET
(
Net-Tune
)
B
B
 
The sub-panels are fixed to the DTR-10.5 with 
two screws at the top and bottom, while the panel 
that covers slots [H] and [I] is fixed with four 
screws at the top and bottom. Keep the removed 
screws for fixing the option board.
 
5
 
Insert the option board along the rail 
softly. When the board comes to the posi-
tion where it stops but does not cover the 
slot completely, push the board forward a 
little bit more strongly.
 
6
 
Fix the option board firmly to the DTR-10.5 
using the removed screws.
 
Be sure to tighten the screws firmly to the 
DTR-10.5. If the screws are loose, contact failures 
for ground or signal wires may occur at the section 
between the DTR-10.5’s slot terminal and the 
option board, which may cause the DTR-10.5 or 
board to fail.
L
R
L
R
FRON
T
CENTER
SURR
SURR 
BACK
SUB
WOOF
ER
SURR
 BACK
  R  
SURR
  R
SUBW
OOFE
R
 (ASSIG
NABLE
)
(SINGLE
)
 (ASSIG
NABLE
)
AUDIO
The i.L
INK log
o is a 
tradem
arks of
 Sony 
Corpor
ation, r
egister
ed 
in the 
U.S. an
d othe
countr
ies.
S400
2
2
1
1
6
6
5
5
4
4
3
3
2
2
1
1
C
D
DIGITAL IN
DIGITA
L IN
OPTIC
AL
COAXIA
L
OUT
E
A
B
PRE O
UT  A
B
L
R
L
R
FRON
T
CENTER
SURR
SURR 
BACK
SUB
WOOF
ER
SURR
 BACK
  R  
SURR
  R
SUBW
OOFE
R
 (ASSIG
NABLE
)
(SINGLE
)
 (ASSIG
NABLE
)
AUDIO
The i.L
INK log
o is a 
tradem
arks of
 Sony 
Corpor
ation, r
egister
ed 
in the 
U.S. an
d othe
countr
ies.
S400
2
2
1
1
6
6
5
5
4
4
3
3
2
2
1
1
C
D
DIGITA
L IN
DIGITAL IN
OPTIC
AL
COAXIA
L
OUT
E
A
PRE O
UT  A
“Net-T
une” 
is a tra
demark
 of 
Onkyo
 Corpo
ration.
ETHERNET
(
Net-Tu
ne)
B
L
R
L
R
FRON
T
CENTER
SURR
SURR 
BACK
SUB
WOOF
ER
SURR
 BACK
  R  
SURR
  R
SUBW
OOFE
R
 (ASSIG
NABLE
)
(SINGLE
)
 (ASSIG
NABLE
)
“Net-T
une” 
is a tra
demark
 of 
Onkyo
 Corpo
ration.
ETHERNET
(
Net-Tu
ne)
AUDIO
The i.L
INK log
o is a 
tradem
arks of
 Sony 
Corpor
ation, r
egister
ed 
in the 
U.S. an
d othe
countr
ies.
S400
2
2
1
1
6
6
5
5
4
4
3
3
2
2
1
1
C
D
DIGITAL IN
DIGITA
L IN
OPTIC
AL
COAXIA
L
OUT
E
A
B
PRE O
UT  A
 
Getting Star
ted