Integra DTR-10.5 ユーザーズマニュアル
80
Enjoying Net Audio
—Continued
The music server settings can be made while you select
the music server as an input source.
the music server as an input source.
Configuring the Music Server
1
Press the [Input] button, and
then roll the scroll wheel to select
MSRV.
then roll the scroll wheel to select
MSRV.
Make sure that the “MSRV” is displayed
when you configure the music server.
when you configure the music server.
2
Press the scroll wheel, and then
press the [Setup] button to display
the Main Menu.
press the [Setup] button to display
the Main Menu.
3
Use the [
]/[
] buttons to select
“Input Setup,” then press the
[Enter] button.
[Enter] button.
ABC
DEF
PQRS
TUV
WXYZ
GHI
JKL
MNO
@.-'/
--/---
Direct Tuning
#
Custom
Display
Dimmer
T V
Input
Sleep
Muting
On
Standby
T V
T V CH
T V VOL
Exit
Gu
ide
Prev
CH
Enter
Set
up
Retu
rn
+10
0
Clear
1
2
3
4
5
6
7
8
9
Input
To
p M
enu
Men
u
VOL
CH
Disc
Disc
I
+
-
+
-
Zone 3
Zone 2
Input
Mode
Macro
Se
rve
r
Aud
io
A
D
J
Input
Setup
Enter,
/
/
/
Scroll wheel
Input
Set
up
Enter
Enter
4
Use the [
]/[
] buttons to select
the “Music Server” sub-menu,
then press the [Enter] button.
then press the [Enter] button.
The setup screen for the sub-menu
appears.
appears.
5
Use the [
] and [
] cursor but-
tons to select “Select Server” and
then use the [
then use the [
] and [
] cursor
buttons to select the desired
server.
server.
Select a network server that exists on the
network.
* mark appears next to the servers
detected on the network. If there is a
server that does not have a * mark, make
sure that the server is running.
“Not Found” message indicates that no
server is currently available for selec-
tion. If the message appears, make sure
that the server is connected and running.
network.
* mark appears next to the servers
detected on the network. If there is a
server that does not have a * mark, make
sure that the server is running.
“Not Found” message indicates that no
server is currently available for selec-
tion. If the message appears, make sure
that the server is connected and running.
6
Press the [Setup] button.
This completes the configuration proce-
dure and the menu disappears.
dure and the menu disappears.
Tips:
When choosing settings on the DTR-10.5,
after selecting the input source using the
input source buttons, press the [Setup]
button. Next, select the menu you want to
configure by turning the [Select/Preset]
dial and press the dial to confirm the
selection. Then, after selecting the sub-
menu you want to configure by turning
the [Select/Preset] dial, select your value
by turning the [Control/Tuning] dial, and
press the dial to confirm the value. If you
want to go back to the previous operation,
press the [Exit] button.
after selecting the input source using the
input source buttons, press the [Setup]
button. Next, select the menu you want to
configure by turning the [Select/Preset]
dial and press the dial to confirm the
selection. Then, after selecting the sub-
menu you want to configure by turning
the [Select/Preset] dial, select your value
by turning the [Control/Tuning] dial, and
press the dial to confirm the value. If you
want to go back to the previous operation,
press the [Exit] button.
Enter
Enter
Enter
Set
up