Integra DTR-7.4 ユーザーズマニュアル
14
Connecting Antenna
This chapter explains how to connect the supplied
indoor FM antenna and AM loop antenna, and how to
connect commercially available outdoor FM and AM
antennas.
indoor FM antenna and AM loop antenna, and how to
connect commercially available outdoor FM and AM
antennas.
The supplied indoor FM antenna is for indoor use only.
If you cannot achieve good reception with the supplied
indoor FM antenna, try using a commercially available
outdoor FM antenna instead (See page 15).
indoor FM antenna, try using a commercially available
outdoor FM antenna instead (See page 15).
The supplied indoor AM loop antenna is for indoor use
only.
only.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using a commercially
available outdoor AM antenna (See page 15).
indoor AM loop antenna, try using a commercially
available outdoor AM antenna (See page 15).
Connecting the Indoor FM Antenna
1
Attach the FM antenna, as shown.
■
USA and Canadian Model
■
Australian Models
Once your DTR-7.4 is ready for use, you’ll need
to tune into an FM radio station and adjust the
position of the FM antenna to achieve the best
possible reception.
to tune into an FM radio station and adjust the
position of the FM antenna to achieve the best
possible reception.
2
Use thumbtacks or something similar to
fix the FM antenna into position.
fix the FM antenna into position.
Caution: Be careful that you don’t injure your-
self when using thumbtacks.
self when using thumbtacks.
FM
75
75
OUT
OUT
OUT
OUT
L
PHONO
PRE OUT
FRONT
SUB
SURR
R
L
AUDIO
R
L
CD
TAPE
R
L
AUDIO
VIDEO
S VIDEO
MONITOR
OUT
R
L
IN
IN
IN
IN
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO
AUDIO
VIDEO
S VIDEO
GND
SURR
BACK/
ZONE 2
R
L
IN
AC INLET
R
CENTER
ETHERNET
(Net -Tune)
(Net -Tune)
R
L
MULTI CH
INPUT
INPUT
FRONT
SUB
SURR
SURR
BACK
BACK
CENTER
R
L
ANTENNA
Y
P
B
P
R
OUTPUT
INPUT 1
Y
P
B
P
R
INPUT 2
Y
P
B
P
R
SURR
BACK/
ZONE 2
SPEAKERS
BACK/
ZONE 2
SPEAKERS
FRONT SPEAKERS
L
R
L
R
SURR SPEAKERS
CENTER
SPEAKER
SPEAKER
R
L
AC OUTLETS
AC 120 V 60 Hz
SWITCHED
TOTAL 120W 1A MAX.
IN
ZONE 2
REMOTE
CONTROL
CONTROL
A
B
OUT
12 V
TRIGGER OUT
TRIGGER OUT
DIGITAL
IN
OPT
2
1
2
3
1
3
COAX
OPT
1
2
DIGITAL
OUT
AV RECEIVER
MODEL NO.
DTR-7.4
RATING: AC 120 V 60 Hz 8.1 A
COMPONENT
VIDEO
I R
RS232
AM
AM antenna push terminals
FM antenna connector
FM antenna connector
FM
75
Insert the plug fully
into the socket.
into the socket.
FM
75
Insert the plug fully
into the socket
into the socket
Thumbtacks, etc.
Connecting the AM Loop Antenna
1
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
the tabs into the base, as shown.
2
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
antenna to the AM push terminals, as
shown.
(The antenna’s wires are not polarity sensitive, so
they can be connected in either terminal.)
Make sure that the wires are attached securely
and that the push terminals are gripping the bare
wires, not the insulation.
they can be connected in either terminal.)
Make sure that the wires are attached securely
and that the push terminals are gripping the bare
wires, not the insulation.
Once your DTR-7.4 is ready for use, you’ll need
to tune into an AM radio station and adjust the
position of the AM antenna to achieve the best
possible reception. Keep the antenna as far away
as possible from your DTR-7.4, TV, speaker
cables, and power cords.
to tune into an AM radio station and adjust the
position of the AM antenna to achieve the best
possible reception. Keep the antenna as far away
as possible from your DTR-7.4, TV, speaker
cables, and power cords.
AM
Push
Insert wire
Release