Integra DTR-7.4 ユーザーズマニュアル
41
Enjoying Music or Videos with the DTR-7.4
—Continued
Temporarily Changing the Speaker Output
Levels
To change the individual speaker volumes temporarily,
follow the procedure given below. Each channel can be
set between –12 and +12 decibels (between –15 and
+12 decibels for the subwoofer). Note that the speaker
volumes will return to the original settings when the
DTR-7.4 is put in the standby state.
follow the procedure given below. Each channel can be
set between –12 and +12 decibels (between –15 and
+12 decibels for the subwoofer). Note that the speaker
volumes will return to the original settings when the
DTR-7.4 is put in the standby state.
Notes:
• You cannot select a speaker if it is set to “No” or
“None” in the Speaker Config Sub-menu of the
Speaker Setup Menu.
Speaker Setup Menu.
• To have your new speaker levels set here, overwrite
the settings at Setup Menu
→
Speaker Setup Menu
→
Level Calibration Sub-menu, and press the Test
Tone button after you complete step 3 in the proce-
dure above.
dure above.
Using the Sleep Timer (remote controller only)
With the sleep timer you can set the DTR-7.4 so that it
automatically turns off after a set period.
automatically turns off after a set period.
Adjusting the brightness of the front display
You can adjust the brightness of the front display of the
DTR-7.4 using the Dimmer button on the remote con-
troller or on the DTR-7.4 front panel (other than Euro-
pean models).
DTR-7.4 using the Dimmer button on the remote con-
troller or on the DTR-7.4 front panel (other than Euro-
pean models).
1
Press the scroll wheel.
2
Press the CH SEL button and
select the desired speaker.
select the desired speaker.
3
Press the Level – or + button to
adjust the volume level.
adjust the volume level.
CH SEL
Level +
Level -
Press the scroll wheel, and then
press the Sleep button repeatedly
to select the required sleep time.
press the Sleep button repeatedly
to select the required sleep time.
You can set the sleep time from 90 to 10
minutes in 10 minute increments.
The Sleep indicator appears on the dis-
play when the sleep timer has been set,
as shown. The specified sleep time
appears on the display for about five sec-
onds, then the previous display reap-
pears.
minutes in 10 minute increments.
The Sleep indicator appears on the dis-
play when the sleep timer has been set,
as shown. The specified sleep time
appears on the display for about five sec-
onds, then the previous display reap-
pears.
To cancel the sleep timer,
press the
Sleep button repeatedly until the Sleep
indicator disappears.
indicator disappears.
To check the remaining sleep time,
press the Sleep button. Note that if you
press the Sleep button while the sleep
time is being displayed, you’ll shorten
the sleep time by 10 minutes.
press the Sleep button while the sleep
time is being displayed, you’ll shorten
the sleep time by 10 minutes.
Using the sleep timer only for Zone 2:
If you are using the remote zone (Zone
2), it will turn off at the same time as the
main zone. If you want to set the sleep
function for Zone 2 only, set the sleep
function with main zone turned on and
then put the main zone into the standby
state.
2), it will turn off at the same time as the
main zone. If you want to set the sleep
function for Zone 2 only, set the sleep
function with main zone turned on and
then put the main zone into the standby
state.
Use the Dimmer button on the
DTR-7.4 to select: dim, dimmer, or
normal brightness.
DTR-7.4 to select: dim, dimmer, or
normal brightness.
On the remote controller, press the
scroll wheel, and then press the
Dimmer button.
scroll wheel, and then press the
Dimmer button.
Sleep
Remote
controller
controller
Dimmer
Dimmer
DTR-7.4
Remote
controller
controller
Enjo
ying Music and Mo
vies