Marantz LN-11S1A ユーザーズマニュアル
6
B
EF
O
RE
U
SE
N
A
M
E O
F P
A
RT
S
B
A
SIC
O
PE
RA
TIO
N
A
D
VA
N
CE
D
O
PE
RA
TIO
N
REM
OT
E C
ON
TR
OLL
ER
OP
ER
ATI
ON
TR
OU
BLE
SH
OO
TIN
G
O
TH
ER
S
SE
TU
P
SETUP
SETUP PROCEDURE
Install the LN-11S1A according to the procedure outlined in the flowchart below.
Start
Mounting
on the floor?
Y
Y
N
N
EXT10
needed?
Prepare the LN-11S1A.
(Page. 7)
Assemble the MOUNT20.
(Page. 7)
Assemble the LN-11S1A.
(Page. 10)
Assemble the EXT10.
(Page. 6)
Mount the LN-11S1A.
(Page. 9)
Mount the LN-11S1A.
(Page. 10)
Mount the LN-11S1A lens.
(Page. 10)
Connect the LN-11S1A.
(Page. 10)
Adjust the LN-11S1A lens.
(Page. 11)
End
ceiling mount
tabletop mount
Completion drawings
EXT10 ASSEMBLY
After reading the “Installation” Section of the
VP-11/VP-15 User Guide and it has been determined
the EXT10 Extension Pole will be needed to meet
the requirements of location and ventilation for
the Projector, assemble the EXT10 by performing
the steps below. If the EXT10 will not be needed,
proceed to LN-11S1A assembly given on page 7.
VP-11/VP-15 User Guide and it has been determined
the EXT10 Extension Pole will be needed to meet
the requirements of location and ventilation for
the Projector, assemble the EXT10 by performing
the steps below. If the EXT10 will not be needed,
proceed to LN-11S1A assembly given on page 7.
Note:
The EXT10 hardware, fasteners and parts list are
located in a separate shipping carton from the
projector.
1.
The EXT10 is adjustable from 43-3/4 inches
to 24 inches as supplied. If the default
range is acceptable proceed to Step 3.
The adjustable range may be changed to
24 inches to 14-5/8 inches by cutting both
poles. When the installation requires the
24 inches to 14-5/8 inches range proceed to
Step 2.
range is acceptable proceed to Step 3.
The adjustable range may be changed to
24 inches to 14-5/8 inches by cutting both
poles. When the installation requires the
24 inches to 14-5/8 inches range proceed to
Step 2.
2.
Cut the Outside Pole to 13-3/8 inches
from the end the mounting plate will be
attached. Cut the Inside Pole to 13-3/4
inches from the end the mounting plate will
be attached. Refer to Figure 5.
attached. Cut the Inside Pole to 13-3/4
inches from the end the mounting plate will
be attached. Refer to Figure 5.
Figure 5
13-3/4”
Cut Here
Inside
Pole
Outside
Pole
Cut Here
13-3/8”
3.
Assemble the Pole Pieces together making
sure to orient them as illustrated in figure
3. Set the Pole Pieces to the desired length
and secure the position using the two
Round Head Philips 1/4-20 x 2-1/4 Screws
and two 1/4- 20 Lock Nuts. Refer to Figure
6.
3. Set the Pole Pieces to the desired length
and secure the position using the two
Round Head Philips 1/4-20 x 2-1/4 Screws
and two 1/4- 20 Lock Nuts. Refer to Figure
6.
Figure 6
14-5/8” to 24”
24 to 43-3/4”
4.
Tighten all the recently installed hardware
and proceed to “PREPARING THE LN-
11S1A”.
11S1A”.