Marantz SR4002/SR5002 ユーザーズマニュアル

This remote controller is capable of learning and 
storing codes used by other remote controls that you 
already own.
For codes which are not learned, the remote 
controller will transmit either the Marantz preset 
codes from the initial settings, or remote codes from 
another manufacturer’s AV equipment which is set 
by the customer.
The receiver sensor for the remote controller signals is 
located at the top of the remote controller.

•  This remote controller is capable to learn around 60 

codes.

• When the batteries are getting weak , the learing 

procedure is not successful.

 

  Place the remote controller so that its infrared 

signal transmitter is facing the infrared signal 
receiver on the Marantz remote controller at a 
distance of about 0.05 m (2 inches).

0.05 m

 

  Press and hold down the SET and MENU 

buttons until LEARN indicator blinks.

 

 Select 

the 

SOURCE button to select the 

SOURCE.

 

  Select the button to be learned.

•  LEARN indicator lights up.

 

  Press and hold the button of the original remote 

controller to learn until the SEND indicator 
blinks twice.

• When the SEND indicator blinks once, repeat this 

step.

• If the LEARN indicator fl ashes when the SEND 

indicator is lit, then the button cannot be learned.

• When the memory of the remote controller is full, 

the LEARN and SEND indicators blink once. If 
you want to learn the code, you should erase other 
learned button.

 Repeat 

steps 

 and 

 to learn other buttons in 

same SOURCE.

 

 Repeat 

steps 

 to 

 to learn other SOURCE.

 

  When you have finished programming the 

remote controller, press the SET button, then 
LEARN indicator stops blinking and exits from 
the LEARN mode.

• When the SEND indicator blinks once again, 

the transmitting code is unavailable for remote 
controller, or the transmitting signal is intercepted 
by noise.

• If no buttons are pressed for approximately 1 

minutes while in the LEARN mode, the remote 
controller automatically exits from the LEARN 
mode.

Codes can be erased in three ways: by buttons, 
sources, and by all memory contents.

 

  Press and hold down the SET and MENU 

buttons until LEARN indicator blinks.

 

 Select 

the 

SOURCE button to select the button 

to be erased.

 

  Press and hold down the SLEEP button and 

press the learned button twice to be erased.
•  SEND indicator blinks twice and the mode 

returns to LEARN mode.

 

  To return the NORMAL mode, press the SET 

button.

 

  Press and hold down the SET and MENU 

buttons until LEARN indicator blinks.

 

  Press and hold down the SLEEP button and 

press the learned SOURCE button twice to be 
erased.
•  LEARN indicator lights.

 

 Press 

ENTER button to continue erasing.

•  The SEND indicator blinks twice and the 

mode returns to LEARN mode.

•  To cancel the erasing operation, do not 

press  ENTER  button and simply touch any 
other button.

 

  To return the NORMAL mode, press the SET 

button.

 

  Press and hold down the SET and MENU 

buttons until LEARN indicator blinks.

 

  Press and hold down the SLEEP button and 

press POWER ON and POWER OFF button.
•  LEARN indicator lights.

 

 Press 

ENTER button to continue erasing.

•  The SEND indicator blinks twice and the 

mode returns to LEARN mode.

•  To cancel the erasing operation, do not 

press  ENTER  button and simply touch any 
other button.

 

  To return the NORMAL mode, press the SET 

button.

Erasing codes will return to the factory preset code, 
or there will leave empty if the button has no factory 
preset code.

SR4002-5002U DFU_01_E1_2.indd   17

SR4002-5002U DFU_01_E1_2.indd   17

07.7.9   2:46:50 PM

07.7.9   2:46:50 PM