Marantz SR4002/SR5002 ユーザーズマニュアル

 3 PREFERENCE
                       
STANDBY MODE  : ECONOMY
TV-AUTO       : 
OSD INFO      : ENABLE

VIDEO CONVERT
HDMI          : ENABLE
DC TRIGGER
              
MAIN  

        EXIT

 

 Select 

“PREFERENCE” in the SETUP MAIN 

MENU with the 

3 or 4 cursor buttons, and 

press the ENTER button.

  To select a desired content, press the 

3 or 4 

cursor buttons.

When this function is set to “ECONOMY”, you can 
reduce the power consumption when the unit is in 
the standby mode. 

TV-AUTO and RS-232C are disabled in the 
“ECONOMY” setting (SR5002 only). 

Select the TV AUTO ON/OFF function to enable or 
disable with the 

1 or 2 cursor buttons.

Select the OSD information function to enable or 
disable with the 

1 or 2 cursor buttons.

If you select “ENABLE”, the unit will display the 
status of the feature (Volume up/down, input 
select, etc..) on the TV monitor. But if you do not 
desire this information, select “DISABLE”.

Select the VIDEO CONVERT function to enable or 
disable with the 

1 or 2 cursor buttons. (Video cable 

connection: Refer to page 20)

 3-1 VIDEO CONVERT

   TV   : ON
   DVD  : ON
   VCR  : ON
   DSS  : ON
   AUX1 : ON

MAIN RETURN         EXIT

After you complete this portion of the set up, move 
the cursor to “MAIN” with the 

3 or 4 cursor buttons 

and press the ENTER button.

This setting determines whether to playback audio 
input to the HDMI jacks through the unit or output 
it through the unit to a TV or projector.
ENABLE:  The audio input to the HDMI jacks 

can be played back by this unit.
In such case, audio signals are not 
output to the TV or projector.

THROUGH: The audio input to the HDMI jacks 

is not output from the speaker 
terminals of the unit. Audio data is 
output directly to the TV or projector. 
This setting is used to listen to audio 
on a multi channel TV, etc.

Select “DC TRIG  SETUP” in the SETUP MAIN 
MENU with 

3 or 4 cursor button, and press the 

ENTER button.

 3-2 DC TIRGGER SETUP
DC TRIG  DISABLE
  
TV   :       TAPE : 
DVD  :       CD/R : 
VCR  :       AUX2 : 
DSS  :       TUNER: 
AUX1 :       7.1CH: 
             

MAIN RETURN         EXIT

You can select MAIN ROOM, MULTI ROOM, 
REMOTE or DISABLE by pressing 

1 or 2 cursor 

buttons.

• REMOTE is available for the external control. The 

RC5001SR cannot operate this function.

• To select desired input source , press 

3 or 4 cursor 

button.

•  To set ON or OFF, press 

1 or 2 cursor button.

• After you complete this portion of the set up, move 

the cursor to “MAIN” with the 

3 or 4 cursor 

buttons and press the ENTER button.

 4 SURROUND

SURR.MODE :AUTO
HT-EQ     :OFF
LFE LEVEL :

MAIN                EXIT

 

 Select 

“SURROUND” in the SETUP MAIN 

MENU with the 

3 or 4 cursor buttons, and 

press the ENTER button.

 

  To select a desired content , press the 

3 or 4 

cursor buttons.

Select the desired surround mode with the 

1 or 2 

cursor buttons.

Select to active the HT-EQ with the 

1 or 2 cursor 

buttons. 
The tonal balance of a film soundtrack will be 
excessively bright and harsh when played back 
over audio equipment in the home. This is because 
fi lm soundtracks were designed to be played back 
in large movie theater environments.
Activating the HT-EQ feature when watching a fi lm 
made for movie theaters corrects this and restores 
the correct tonal balance.
The HT-EQ feature is available except in the 
following modes.

• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
• When VIRTUAL is set for the surround mode

Select the output level of the LFE signal included in 
the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the 

1 or 2 cursor 

buttons.

After you complete this portion of the set up, move 
the cursor to “MAIN” with the 

3 or 4 cursor buttons 

and press the ENTER button.

• If MRAC is started with both speaker settings A 

and B off, it will enter CANCEL mode without 
displaying an ERROR on the screen. When this 
happens, check the SPEAKER setting.

• The measured speaker distance may differ from the 

actual distance from speakers. Nevertheless, the 
measured value is suitable for the speakers.

• To make changes to individual speakers, select 2. 

SPEAKER SETUP on the SETUP MAIN MENU, 
then select MANUAL for 2-1 SPEAKER SETUP.

•  The included microphone is designed specifi cally for 

this receiver. Other microphones do not guarantee 
suitable measurement results. Use the included 
microphone to conduct measurements.

• During measurement, press the ENTER or EXIT 

button to cancel measurement.

• In some rooms, an error may occur during auto 

speaker setup or it may not be possible to set Speaker 
distance correctly because of room acoustics. In 
such case, set the speaker distance by MANUAL 
setup.

• Please set any THX Certifi ed speakers manually 

to “Small” and the crossover to “80 Hz” after Auto 
setup operation.

•  When only HDMI components are connected, OSD 

will not be displayed.

Error Indications During Measurement
If trouble occurs during measurement, an error 
message is displayed on the monitor screen and 
FL display. Those errors and their remedies are 
described below. The message appearing on the FL 
display is given in (  ).

MIC SETUP ERROR (MIC SET ERROR)

The microphone (MC-10) is not properly connected.

→  Check the microphone connection.

AMBI NOISE ERROR (AMBI NOISE ER)

Measurement cannot be done correctly because of 
excessive ambient noise.
→  Either temporarily turn off power to noisy 

devices such as air conditioning or move them 
out of the room.

→  Retry measurement when the room is quiet.
SPEAKER SET ERROR (SPK SET ERROR)

The speakers are not properly connected.
→  Recheck speaker layout and connections.

SR4002-5002U DFU_01_E2_2.indd   31

SR4002-5002U DFU_01_E2_2.indd   31

07.7.9   2:47:33 PM

07.7.9   2:47:33 PM