Marantz SR5001 ユーザーズマニュアル

 6 CS II PARAMETER

TRUBASS      : 0
SRS DIALOG   : 0

MAIN                EXIT

 

 Select 

“

” in the SETUP MAIN MENU 

with the 

3

 or 

4

 cursor buttons, and press the 

 button.

 

  To Select desired contents as below, press the 

3

 or 

4

 cursor buttons.

Set the TRUBASS level between 0 and 6 level in 1 
level interval with the 

1

 or 

2

 cursor buttons.

TRUBASS produced by the speakers are an octave 
below the actual physical capabilities of the speakers 
adding exciting, deeper bass effects.

Set the SRS DIALOG level between 0 and 6 in 1 
level intervals with the 

1

 or 

2

 cursor buttons.

This can be popped out of the surround audio 
effects, allowing the listener to easily discern what 
the actors say.
If “

” was selected for the Center speaker 

setting, in the Speaker size set up menu, then this 
setting will not appear.

After you complete this portion of the set up, move 
cursor to “

” with the 

3

 or 

4

 cursor buttons and 

press the 

 button.

Select the VIDEO CONVERT function to enable 
or disable with the 

1

 or 

2

 cursor buttons. (Video 

cable connection: Refer to page 19)

 3-1 VIDEO CONVERT

   TV   : ON
   DVD  : ON
   VCR1 : ON
   DSS  : ON
   AUX1 : ON

MAIN RETURN         EXIT

After you complete this portion of the set up, move 
the cursor to “

” with the 

3

 or 

4

 cursor buttons 

and press the 

 button.

This setting determines whether to playback audio 
input to the HDMI jacks through the SR4001/
SR5001 or output it through the receiver to a TV 
or projector.

  The audio input to the HDMI jacks 

can be played back by this receiver.
In such case, audio signals are not 
output to the TV or projector.

 The audio input to the HDMI jacks is 

not output from the speaker terminals 
of the SR4001/SR5001. Audio data is 
output directly to the TV or projector. 
This setting is used to listen to audio 
on a multi channel TV, etc.

Select “

” in the SETUP MAIN 

MENU with 

3

 or 

4

 cursor button, and press the 

 button.

 3-2 DC TIRGGER SETUP
DC TRIG  DISABLE
  
TV   :       CD   : 
DVD  :       TAPE : 
VCR1 :       CD-R : 
DSS  :       AUX2 : 
AUX1 :       TUNER: 
             7.1CH:

MAIN RETURN         EXIT

You can select MAIN ROOM, MULTI ROOM, 
REMOTE or DISABLE by pressing 

1

 or 

2

 cursor 

buttons.

• REMOTE is available for the external control. The 

RC5001SR cannot operate this function.

• To select desired input source , press 

3 or 4 cursor 

button.

•  To set ON or OFF, press 

1 or 2 cursor button.

• After you complete this portion of the set up, move 

the cursor to “MAIN” with the 

3 or 4 cursor 

buttons and press the ENTER button.

 4 SURROUND

SURR.MODE :AUTO
HT-EQ     :OFF
LFE LEVEL :

MAIN                EXIT

 

 Select 

“

” in the SETUP MAIN 

MENU with the 

3

 or 

4

 cursor buttons, and 

press the 

 button.

 

  To select a desired content , press the 

3

 or 

4

 

cursor buttons.

Select the desired surround mode with the 

1

 or 

2

 

cursor buttons.

Select to active the HT-EQ with the 

1

 or 

2

 cursor 

buttons. 
The tonal balance of a film soundtrack will be 
excessively bright and harsh when played back 
over audio equipment in the home. This is because 
fi lm soundtracks were designed to be played back 
in large movie theater environments.
Activating the HT-EQ feature when watching a fi lm 
made for movie theaters corrects this and restores 
the correct tonal balance.
The HT-EQ feature is available except in the 
following modes.

• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode

Select the output level of the LFE signal included in 
the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the 

1

 or 

2

 cursor 

buttons.

After you complete this portion of the set up, move 
the cursor to “

” with the 

3

 or 

4

 cursor buttons 

and press the 

 button.

Pro Logic 

II

-Music mode creates a rich and enveloping 

surround ambience from stereo sources such as 
CDs.
In this mode, SR4001/SR5001 includes three controls 
to fi ne-tune the soundfi eld as follows. 

 5 PL II MUSIC PARAMETER

PARAMETER    : DEFAULT

PANORAMAA    : OFF
DIMENSION    :  3
CENTER WIDTH :  3

MAIN                EXIT

Select “

” in the SETUP MAIN MENU 

with the 

3

 or 

4

 cursor buttons, and press the 

 

button.

Select “

” or “

” with the 

1

 or 

2

 

cursor buttons.
If you select “

”, you can adjust three 

parameters as listed below. 

Select the Panorama mode On or Off with the 

1

 or 

2

 cursor buttons.

Panorama wraps the sound of the front left and right 
speakers around you, for an exciting perspective.

Set the Dimension level between +3 and –3 level 
in 1 level intervals with the 

1

 or 

2

 cursor buttons.

Adjust the soundfi eld either towards the front or 
towards the rear.
This can be useful to help achieve a more 
suitable balance from all the speakers with certain 
recordings.

Set the Center width level between 0 and 7 in 1 
level intervals with the 

1

 or 

2

 cursor buttons.

Center Width allows you to gradually spread the 
center channel sound into the front left and right 
speakers. 
At its widest setting, all the sound from the center 
is mixed into the left and right. 
This control may help achieve a more spacious 
sound or a better blend for the front image.
If “

” was selected for the Center speaker 

setting, in the Speaker size set up menu, then this 
setting will not appear.

After you complete this portion of the set up, move 
cursor to “

” with the 

3

 or 

4

 cursor buttons and 

press the 

 button.