Pioneer VSX-D3S ユーザーズマニュアル

<

ARB7050

>

12

~ TWO VOLTAGE SELECTORS switches

See page 4.

! TAPE 1 jacks

Connect to the first cassette deck.

@ CD input jacks

Connect to the output jacks of a compact disc player.

# VCR 1 jacks

[VIDEO OUT]
Connect to the VCR 1 VIDEO INPUT jack.
[AUDIO OUT (L, R)]
Connect to the VCR 1 AUDIO INPUT jacks.
[VIDEO IN]
Connect to the VCR 1 VIDEO OUTPUT jack.
[AUDIO IN (L, R)]
Connect to the VCR 1 AUDIO OUTPUT jacks.

$ LD input jacks

Connect to an LD player’s output jacks (audio, video).

% TV/SAT (Satellite) jacks (input)

Use these jacks if you wish to connect a TV tuner with both video
and audio outputs.

^ S (connector) video jacks

When used in conjunction with a VCR, LD player or TV monitor
equipped with S video jacks, connect to these jacks. (Refer to
page 8.)

÷ TO MONITOR TV jack

This unit uses the TV screen to operate the system. Set the rear
panel PAL/NTSC switch (3) to match your TV's color system
(Multi-voltage model only). The screen will be unclear if the
color system does not match.

& AC-3 

This jack is ready for future AC-3 system digital TV audio
broadcasts.

NOTE:
Do not connect to a CD or DAT coaxial digital audio output.

* AC-3 

Connect to an LD player’s AC-3 • RF OUT jack.

( CENTER SPEAKERS terminals

Connect the center speaker(s) to these terminals.

NOTE:
Do not allow any of the cord’s conductors to protrude from the
terminals or touch any other conductors. Malfunctions or
breakdowns may occur when conductors come into contact
with each other.
Use a center speaker with an impedance of 8 

Ω

 to 16 

Ω

. (If you

connect two center speakers, use speakers with an impedance
of 4 

Ω

 to 16 

Ω

. Refer to 

_

.)

) REAR SPEAKERS terminals

Connect the rear speakers to these terminals.

NOTE:
Do not allow any of the cord’s conductors to protrude from the
terminals or touch any other conductors. Malfunctions or
breakdowns may occur when conductors come into contact
with each other.
Use rear speakers with an impedance of 8 

Ω

 to 16 

Ω

.

_ CENTER SPEAKER SELECTOR switch

This switch changes the speaker impedance when only one
center speaker is connected, or two speakers are connected.
When only one speaker is connected:
Be sure to set the switch to “

Ι

 ONLY” (down side), and always

connect a speaker with an impedance of 8 

Ω

 to 16 

Ω

 to the 

Ι

terminal.
When two speakers are connected:
Be sure to set the switch to “

Ι

 + 

ΙΙ

” (up side), and always use

speakers with an impedance of 4 

Ω

 to 16 

Ω

.

NOTE:
Switch the CENTER SPEAKER SELECTOR when the unit power
supply is at STANDBY. Do not switch the selector when the
power supply is at ON.

+ FRONT SPEAKERS terminals

A : Connect to the first set of speakers.
B : Connect to the second set of speakers.

NOTE:
Do not allow any of the cord’s conductors to protrude from the
terminals or touch any other conductors. Malfunctions or
breakdowns may occur when conductors come into contact
with each other.
Use front speakers with an impedance of 8 

Ω

 to 16 

Ω

.

¡ AC OUTLETS

(U.S. and Canadian models)
[SWITCHED TOTAL 100 W (0.8 A) MAX]
Power supplied through these outlets is turned on and off by the
receiver’s POWER switch. Total electrical power consumption
of connected equipment should not exceed 100 W (0.8 A).
[UNSWITCHED 100 W (0.8 A) MAX]
Power flows continually to this outlet, regardless of whether the
receiver is switched ON or OFF. Electrical power consumption
of the connected equipment should not exceed 100 W (0.8 A).

(Multi-voltage model)
[SWITCHED TOTAL 100 W  MAX]
Power supplied through these outlets is turned on and off by the
receiver’s POWER switch. Total electrical power consumption
of connected equipment should not exceed 100 W.
[UNSWITCHED 100 W MAX]
Power flows continually to this outlet, regardless of whether the
receiver is switched ON or OFF. Electrical power consumption
of the connected equipment should not exceed 100 W.

÷

This unit should be disconnected by removing the power plug
from the wall socket when not in regular use, e.g. when on
vacation.

÷

 Do not connect appliances with high power consumption such

as heaters, irons or television sets to these AC OUTLETS in
order to avoid overheating and fire risk. This can cause the
receiver to malfunction.

™ Power cord