Marantz SC-7S1 ユーザーズマニュアル
13
Rear panel
5. Name and function
1
Input Balanced terminal
This terminal is to connect the components which have bal-
anced outputs i.e. SACD, CD Player.
When Bi-Amping, terminal B can not be used.
Balanced terminal
anced outputs i.e. SACD, CD Player.
When Bi-Amping, terminal B can not be used.
Balanced terminal
→
p5
2
Input SACD/CD, Line 1, Line 2, Tape (Un-
balanced) terminal
balanced) terminal
This terminal is to connect the unbalanced terminals of compo-
nents., i.e. SACD, CD etc.
When Bi-Amping, terminal B can not be used.
nents., i.e. SACD, CD etc.
When Bi-Amping, terminal B can not be used.
3
REC out terminal
The terminal connects to the Input of Recording equipment i.e.
CD Recorders, DAT etc.
When Bi-Amping, the signal being input to channel A, will be
output to both A & B channels.
CD Recorders, DAT etc.
When Bi-Amping, the signal being input to channel A, will be
output to both A & B channels.
4
Pre out Unbalanced 1,2 terminal
This connects to the un balanced inputs of a Power Amp. When
Bi-Amping, the signal being input to channel A, will be output to
both A & B channels.
Bi-Amping, the signal being input to channel A, will be output to
both A & B channels.
5
Pre out Balanced terminal
This terminal is connected to the Balanced input of the Power
Amplifier. When Bi-Amping, the signal being input to channel A,
will be output to both A & B channels.
Amplifier. When Bi-Amping, the signal being input to channel A,
will be output to both A & B channels.
6
Remote control In/Out terminals
These terminals are for connecting one or more SC-7S1s to
each other. The IN is for receiving control signals. The OUT is for
sending Control signals.
each other. The IN is for receiving control signals. The OUT is for
sending Control signals.
7
ID No. switch
Whilst several SC-7S1 are connected, to set up respective ID
No. to distinguish each products.
When only 1 unit is used, the No. will be set 1. Initial
setting is <1>.
This switch is to give ID numbers to each SC-7S1, when two or
more are used. When using only 1, SC-7S1 the ID switch is set
to 1. Factory setting is 1.
Trim adjustment in case of several units of SC-7S1
No. to distinguish each products.
When only 1 unit is used, the No. will be set 1. Initial
setting is <1>.
This switch is to give ID numbers to each SC-7S1, when two or
more are used. When using only 1, SC-7S1 the ID switch is set
to 1. Factory setting is 1.
Trim adjustment in case of several units of SC-7S1
→
p18
If using 2 or more SC-7S1s, you can use the trim Adjustment.
See page 18.
See page 18.
8
Mode switch
The switch to change Stereo mode and Bi-Amp mode.
Initial setting is <stereo>.
Initial setting is <stereo>.
●
In case the SC-7S1 is used for normal 2 channel.
Setting <Stereo> mode.
●
In case of complete Bi-Amp connection with 2 units of SC-
7S1.
Setting <Bi-Amp> mode.
In case of <Bi-Amp> mode, the signal input from A
channel will be out to both of A/B channels through the
Pre-out terminal and REC out terminal.
Then, the input terminal on B channel can not be used.
7S1.
Setting <Bi-Amp> mode.
In case of <Bi-Amp> mode, the signal input from A
channel will be out to both of A/B channels through the
Pre-out terminal and REC out terminal.
Then, the input terminal on B channel can not be used.
This switch is to switch between Stereo & Bi-Amp Mode. Fac-
tory setting is Stereo. Stereo is used for using only 1 SC-7S1. If
using 2 or more SC-7S1s, you will set the switch to Bi-Amp
Mode. When Bi-Amping, the signal being input to channel A,
will be outputted to both A & B channels through the Pre-out &
REC out terminals. The B input terminal can not be used in Bi-
Amp Mode.
tory setting is Stereo. Stereo is used for using only 1 SC-7S1. If
using 2 or more SC-7S1s, you will set the switch to Bi-Amp
Mode. When Bi-Amping, the signal being input to channel A,
will be outputted to both A & B channels through the Pre-out &
REC out terminals. The B input terminal can not be used in Bi-
Amp Mode.
9
AC IN socket
Connect to a household power outlet with supplied AC CORD.