Kicker S18X ユーザーズマニュアル

Fit the SPAIR to the BAM with the 
four (4) 1/4”-20 Acorn Head Nuts and
washers, and the eight (8) Acorn Head
Bolts. We have enclosed four (4) extra
Acorn Head Bolts. See Figure 18.

Hand tighten the Acorn Head Nuts and

Bolts in the order shown in Figure 19.

Then use a wrench or socket driver to

securely fasten the bolts. This will

ensure a proper fit and alignment.

Contact your International Kicker dealer or distributor concerning specific procedures for your country's warranty
policies.

WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing!
Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an
undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too
loud and may permanently damage your hearing. Please use common sense when controlling volume.

Comuníquese con su concesionario o distribuidor Kicker internacional para obtener infor ación sobre procedimientos
específicos relacionados con las normas de garantía de su país.

ADVERTENCIA: Los excitadores Kicker son capaces de producir niveles de sonido que pueden dañar
permanentemente el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el
oído que escuchar un sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es
muy fuerte y que puede dañar permanentemente el oído. Sea precavido cuando controle el volumen.

Nehmen Sie mit Ihren internationalen Kicker-Fachhändler oder Vertrieb Kontakt auf, um Details über die
Garantieleistungen in Ihrem Land zu erfahren.

WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann!
Wenn Sie ein System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein
nicht verzerrtes System auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass
der Schallpegel zu laut ist und zu permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung
bitte vernünftig!

Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou
distributeur International Kicker.

AVERTISSEMENT: Les haut-parleurs Kicker ont la capacité de produire des niveaux sonores pouvant endommager
l'ouïe de façon irréversible ! L'augmentation du volume d'un système jusqu'à un niveau présentant une distorsion
audible endommage davantage l'ouïe que l'écoute d'un système sans distorsion au même  volume. Le seuil de la
douleur est toujours le signe que le niveau sonore est trop élevé et risque d'endommager l'ouïe de façon irréversible.
Réglez le volume en faisant prevue de bon sens !

SOLOXSUBWOOFER

03062007+07SOLOX

P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510

SoloX subwoofers will handle massive amounts of power in any of the

recommended enclosures, minimum or maximum. The smaller enclosures are best for use in limited-space

applications. The larger recommended enclosures will yield more bass at the resonate frequency of the enclosure.

The listed Power Handling capacities assume that both voice coils are in use with the appropriate sub-sonic/resonate

frequency filter. Always connect both coils in a dual voice-coil speaker.

Please follow these instruction to insure proper installation. 

Use a jigsaw or router to cut the woofer cutout. Use a 7/16”

(11mm) drill bit for the mounting holes. See Figure 11.

Insert the SPLAT into the cutout (inside the enclosure) and move it into
position. See Figure 12.

Use masking tape to temporarily

hold the SPLAT in place inside

the enclosure. This will be

necessary for securing the BAM.

This tape can be removed after

the corner fastening

hardware has been installed.

See Figure 13.

With the help of an assistant, insert the BAM and start
fastening the corner hardware. Remove the masking tape.
Tighten the double-end threaded studs to secure the BAM
to the enclosure baffle.
See Figure 14.

Pull the speaker cable wires (used to connect the subwoofer to the

amplifier) through the BAM and connect them to the SPAIR’s

Binding Posts. The Locator Pin and Locator Hole will properly align

the SPAIR to the BAM.

See Figure 15.

Remove the Gap Cap before
inserting the SPAIR.  
See Figure 16.

Carefully insert the SPAIR back into

the BAM; do not damage the voice

coil. The double-end threaded studs

and the ARCTIC (Aluminum Rapid

Cooling Thermal Induction Centering)

Cap, located on the top of the

extended pole piece of the SPAIR, will help to center the SPAIR as you

lower it into the BAM. When properly aligned these assemblies easily

slide together. See Figure 17.