JVC LVT0027-005A ユーザーズマニュアル
6
English
■
■
Common Operations
AUX
BASS+
DISPLAY
TREBLE+,–
STANDBY
indicator
indicator
AUX
AHB (ACTIVE
HYPER BASS)
PRO
HYPER BASS)
PRO
PHONES
ACTIVE HYPER
BASS PRO
BASS PRO
VOLUME+,–
VOLUME+,–
Turning the System On ——————
Press the
button.
The display comes on and the STANDBY indicator goes out.
The System comes on ready to continue in the mode it was in when
the power was last turned off.
The System comes on ready to continue in the mode it was in when
the power was last turned off.
■
For example, if the last thing you were doing was listening to a
tape, you are now ready to listen to a tape again. If you wish,
you can change to another source.
tape, you are now ready to listen to a tape again. If you wish,
you can change to another source.
■
If you were listening to the Tuner last, the Tuner comes on play-
ing the station it was last set to.
ing the station it was last set to.
Turning the System Off ——————
Press the
button again.
The STANDBY indicator lights up and the display is blank, except
for the clock display.
for the clock display.
■
Some power (2.9W) is always consumed even though power is
turned off (called Standby Mode).
turned off (called Standby Mode).
■
To switch off the Unit completely, unplug the AC power cord
from the AC outlet (or, if using a car adaptor, unplug that from
the unit). When you unplug the AC power cord, the clock will
be reset to 0:00 immediately, and preset Tuner stations will be
erased after about 24 hours.
from the AC outlet (or, if using a car adaptor, unplug that from
the unit). When you unplug the AC power cord, the clock will
be reset to 0:00 immediately, and preset Tuner stations will be
erased after about 24 hours.
Press the VOLUME + button to increase the volume or press the
VOLUME – button to decrease it.
You can adjust the volume level between 0 and 50.
VOLUME – button to decrease it.
You can adjust the volume level between 0 and 50.
CAUTION:
The Volume cannot be adjusted while the Unit is
in Standby mode. DO NOT turn on the Unit and/or
start playing any source without first setting the
VOLUME control to 0, as a sudden blast of sound
can damage your hearing, speakers and/or head-
phones.
The Volume cannot be adjusted while the Unit is
in Standby mode. DO NOT turn on the Unit and/or
start playing any source without first setting the
VOLUME control to 0, as a sudden blast of sound
can damage your hearing, speakers and/or head-
phones.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
You can reinforce the bass sound to maintain rich, full bass at low
volume (you can use this effect only for playback):
volume (you can use this effect only for playback):
To get the effect,
press the ACTIVE HYPER BASS PRO button.
The “BASS” indicator lights up on the display.
To cancel the effect,
press the button again.
The “BASS” indicator goes out.
You can control the tone by changing the bass and treble.
BASS control ————————————
You can adjust the bass level (low frequency range level) between
–6 and 6. (0: Flat)
–6 and 6. (0: Flat)
To emphasize the bass level,
press the BASS+ button on the
Remote Control.
To lower the bass level,
press the BASS– button on the Remote
Control.
Turning the Power On and Off
Adjusting the Volume
Reinforcing the Bass Sound
Tone Control
UX-Eng.fm Page 6 Thursday, March 5, 1998 6:42 PM