JVC CA-MXGA77 ユーザーズマニュアル
9
Common Operations
Turning On or Off the Power
To turn on the unit, press
so that the
STANDBY lamp goes off.
To turn off the unit (on standby), press
again so that the STANDBY lamp lights up.
again so that the STANDBY lamp lights up.
A little power is always consumed even
while the unit is on standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
while the unit is on standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
When you unplug the AC power cord or if a power
failure occurs
failure occurs
The clock is reset to “– – : – –” soon, while the tuner preset stations
(see page 12) will be erased in a few days.
(see page 12) will be erased in a few days.
Saving the Power Consumption While on
Standby—ECO Mode
Standby—ECO Mode
You can save the power consumption while the unit is turned
off (on standby).
off (on standby).
To activate the ECO mode, press ECO
while the unit is turned off (on standby).
The display illumination (including the
display demonstration) disappears.
while the unit is turned off (on standby).
The display illumination (including the
display demonstration) disappears.
To deactivate the ECO mode, press ECO again.
The display illumination appears.
• Turning on the unit also deactivates the ECO mode.
The display illumination appears.
• Turning on the unit also deactivates the ECO mode.
About the ECO mode
While the ECO mode is activated, the display demonstration is
canceled temporarily.
canceled temporarily.
Setting the Clock
Before operating the unit any further, first set the clock built
in this unit. You can set the clock whether the unit is on or
off.
in this unit. You can set the clock whether the unit is on or
off.
On the unit ONLY:
1
Press CLOCK/TIMER.
The hour digits start flashing on the display.
2
Turn the
4/¢ control to adjust
the hour, then press SET.
The minute digits start flashing on the
display.
display.
• If you want to correct the hour after pressing SET,
press CANCEL/DEMO. The hour digits start
flashing again.
flashing again.
3
Turn the
4/¢ control to
adjust the minute, then press SET.
To check the clock time
Press DISPLAY while playing any source.
• Each time you press the button, the source
• Each time you press the button, the source
indication and the clock time alternate on the
display.
display.
To adjust the clock again
If you have adjusted the clock before, you need to press
CLOCK/TIMER repeatedly until “CLOCK” is selected.
• Each time you press the button, the clock/timer setting
CLOCK/TIMER repeatedly until “CLOCK” is selected.
• Each time you press the button, the clock/timer setting
modes change as follows:
If there is a power failure
The clock loses the setting and is reset to “– – : – –.” You need to set
the clock again.
the clock again.
Selecting the Sources
To listen to the radio, press FM/AM. (See page 12.)
To play back CDs, press CD
To play back CDs, press CD
6. (See pages 15 – 21.)
To play back tapes, press TAPE
3. (See page 22.)
To select the external equipment as the source, press AUX.
When you press the play button for a particular source (AUX,
FM/AM, CD
FM/AM, CD
6, and TAPE 3), the unit turns on (and the
unit starts playing the source if it is ready—COMPU PLAY
CONTROL).
CONTROL).
ECO
STANDBY
ON TIME
(Daily Timer)
DAILY
Canceled
ON TIME
(Recording Timer)
CLOCK
REC
ECO
STANDBY
CLOCK
/ TIMER
DISPLAY
SET
SET
ECO
STANDBY
09_10MXGT88&GA77[B].pm6
03.2.8, 9:01 PM
9