JVC CA-UXG30 ユーザーズマニュアル
19
Timer Operations
(see pages 16 and 17)
• When you unplug the AC power cord or if a power failure
occurs, the timer will be canceled. You need to set the
clock first, then the timer again.
clock first, then the timer again.
Troubleshooting
If you are having a problem with your System, check this list
for a possible solution before calling for service.
for a possible solution before calling for service.
General:
Adjustments or settings are suddenly canceled before
you finish.
]
you finish.
]
There is a time limit. Repeat the procedure again.
Operations are disabled.
]
]
The built-in microprocessor may malfunction due to
external electrical interference.
external electrical interference.
Unplug the AC power
cord and then plug it back in.
Unable to operate the System from the remote control.
]
]
The path between the remote control and the remote
sensor on the System is blocked.
sensor on the System is blocked.
]
The batteries are exhausted.
No sound is heard.
]
]
Speaker connections are incorrect or loose.
]
Headphones are connected.
Radio Operations:
Hard to hear broadcasts because of noise.
]
]
Antennas connections are incorrect or loose.
]
The AM loop antenna is too close to the System.
]
The FM antenna is not properly extended and positioned.
Disc Operations:
The disc does not play.
]
]
The disc is placed upside down. Place the disc with the
label side up.
label side up.
ID3 Tag on an MP3 disc cannot be shown.
]
]
There are two types of ID3 Tag—Version 1 and Version
2. This System can only show ID3 Tag Version 1.
2. This System can only show ID3 Tag Version 1.
MP3 groups and tracks are not played back as you
expect.
]
expect.
]
The playing order is determined when the disc was
recorded. It depends on the writing application.
recorded. It depends on the writing application.
The disc sound is discontinuous.
]
]
The disc is scratched or dirty.
The disc tray does not open or close.
]
]
The AC power cord is not plugged in.
]
Child Lock is in use (see page 15).
Timer Operations:
Daily Timer does not work.
]
]
The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
Timer starts working only when the System is turned off.
Maintenance
To get the best performance of the System, keep your discs,
and mechanism clean.
and mechanism clean.
Handling discs
• When removing the disc from its case, hold it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use to prevent warping.
• Be careful not to scratch the surface of the disc.
• Avoid exposure to direct sunlight, extreme temperature,
• Put the disc back in its case after use to prevent warping.
• Be careful not to scratch the surface of the disc.
• Avoid exposure to direct sunlight, extreme temperature,
and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System
is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe clean
with a dry cloth.
diluted neutral detergent and wrung well, then wipe clean
with a dry cloth.
• Since the System may deteriorate in quality, become
damaged or have its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
insecticides to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
To remove the speaker grilles:
Holes
Projections
Speaker
grille
grille
UX-G30[B].book Page 19 Tuesday, February 14, 2006 5:00 PM