JVC NX-DV3 ユーザーズマニュアル
40
1
Press
and to select "SURR"
(Surround Speaker) or "SUBWFR"
(Sub-woofer).
2
Select
or
to adjust the
volume.
Adjust the volume between -6 to +6.
• It will return to sound source display in a
few seconds.
NOTE
• When the speaker position is "R", adjust the vol-
ume of the left "SURR L" surround speaker and the
right "SURR R" surround speaker separately.
right "SURR R" surround speaker separately.
• In the following situations, "SUBWFR" cannot be
adjusted.
• "SUB WFR" is set to "OFF" in "Other Settings"
• "SUB WFR" is set to "OFF" in "Other Settings"
on the right.
• The sound source with stereo sound is played.
• The sound source is DVD and the disc is
• The sound source is DVD and the disc is
stopped.
1
Press .
2
Select a setting item by pressing
or
.
3
Press
to set or adjust the
level.
BAL:
Turning down the volume of the left or right
speaker. To turn down the volume of the right
Turning down the volume of the left or right
speaker. To turn down the volume of the right
speaker, press
(R-1-R-21), to turn down the
volume of the left speaker, press
(L-1-L-21).
The volume level changes each time the button is
pressed. When the balance is right, it displays
"CENTER".
pressed. When the balance is right, it displays
"CENTER".
SUB WFR:
When a sub-woofer is connected to the unit, select
"ON".
When a sub-woofer is not connected, select
"OFF".
When a sub-woofer is connected to the unit, select
"ON".
When a sub-woofer is not connected, select
"OFF".
DEC1, 2:
This allows you to set to the decode mode when
external equipment connected to Digital 1 or 2
uses Dolby Digital or DTS, or when an equipment
such as a BS digital tuner is connected to Digital 1
or 2. It is helpful in the following situations:
This allows you to set to the decode mode when
external equipment connected to Digital 1 or 2
uses Dolby Digital or DTS, or when an equipment
such as a BS digital tuner is connected to Digital 1
or 2. It is helpful in the following situations:
• When the sound is not audible at the beginning
of the playback.
• When noise is heard when selecting a chapter.
AUTO/PCM:Normally this mode should be
selected.
DTS:
This mode should be selected when
the sound is DTS. Other sounds than
DTS are not heard.
the sound is DTS. Other sounds than
DTS are not heard.
• It allows you to return to source (sound source)
display a few seconds later.
Adjust the Volume for Each
Speaker
■Dolby Pro Logic II
Dolby Pro-Logic II allows you to enjoy 2 channels
source (sound source) such as CD with surround
effect. There are two modes as follows:
source (sound source) such as CD with surround
effect. There are two modes as follows:
• Pro Logic movie(PLII MOVIE)
: Surround used for movie software
• Pro Logic Music (PLII MUSIC)
: Surround used for music software
When Dolby Pro Logic II Surround is used,
appears in the display window.
■All Channel Stereo (ALL CH ST.)
This mode allows you to listen to stereo sound
while playing the 2-channel source (sound
source) such as a CD, by using the four speakers
of the unit. In this way, it is possible to enjoy
broader stereo sound compared with the sound
produced by two speakers.
while playing the 2-channel source (sound
source) such as a CD, by using the four speakers
of the unit. In this way, it is possible to enjoy
broader stereo sound compared with the sound
produced by two speakers.
Other Settings
Adjust the volume balance of the front
speakers.
speakers.
Set whether a sub-woofer is to be used.
Set the decode mode for Digital 1
Terminal.
Terminal.
Set the decode mode for Digital 2
Terminal.
Terminal.
NX-DV3[UJ].book 40 ページ ２００４年１２月２８日 火曜日 午後２時３７分