Manualsbrain.com
  1. マニュアル
  2. ブランド
  3. JVC
  4. CA-MXJ777V
  5. ユーザーズマニュアル

JVC CA-MXJ777V ユーザーズマニュアル

ダウンロード
ページ / 39
20
English
4
ONLY FOR “PRO LOGIC”
Press DELAY TIME repeatedly to select
the proper delay time of the rear speaker
output.
• Each time you press the button, the delay time changes as
follows.
DELAY1:
Select this when the distance from you to your rear
speakers is greater than that to the front speakers.
DELAY2:
Select this when the distance from you to your rear
speakers is almost equal to that to the front speakers.
DELAY3:
Select this when the distance from you to your rear
speakers is less than that to the front speakers.
DELAY4:
Select this when the distance from you to your rear
speakers is much less than that to the front speakers.
5
Press TEST TONE to check the speaker
output balance.
A test tone comes out of the speakers in the following
order:
DELAY TIME
DELAY1
DELAY2
DELAY4
DELAY3
TEST TONE
LEFT
(Left front speaker)
SURROUND
(Rear speakers)
CENTER
(Center speaker)
RIGHT
(Right front speaker)
* “CENTER” does not appear when selecting “PHANTOM”
or “OFF” for the center mode, and no test tone comes out of
the center speaker.
6
Press VOLUME + / – ™ to adjust the
test tone volume to a proper level.
7
If necessary, adjust the speaker output balance so
that the output level from center and rear speakers
is almost equal to that from the front speakers:
To adjust the center speaker output
level (from –10 to +10),
 press CENTER
LEVEL – / +.
• You cannot adjust the center speaker output level
when you select “PHANTOM” or “OFF” for the center mode.
To adjust the rear speaker output level
(from –10 to +10),
 press REAR LEVEL – / +.
• You cannot adjust the right and left speaker
output levels separately.
• You cannot adjust the rear speaker output level
when using Dolby 3 Stereo.
8
Press TEST TONE again to stop the test
tone.
9
Release SHIFT 9.
CENTER
LEVEL
+
–
REAR
LEVEL
+
–
*
TEST TONE
Enjoying Playback with Dolby Surround
You can use the settings you have already stored in memory.
On the unit:
On the unit:
1
Press PRO LOGIC/3 STEREO c button to
select  the Dolby Surround mode you want.
The PRO LOGIC or 3 STEREO indicator lights up
on the display.
PRO LOGIC
/ 3 STEREO
PRO LOGIC
3 STEREO
Cancelled
• When Dolby Surround is activated, the sound mode is
cancelled temporarily.
2
Select and play a sound source encoded with Dolby
Surround. (with the 
DOLBY SURROUND
 mark).
To cancel the Dolby Surround mode, press PRO LOGIC /
3 STEREO repeatedly until neither PRO LOGIC nor
3 STEREO indicator remains lit on the display.
On the remote control:
On the remote control:
1
Press and hold SHIFT 9 until the following
procedure is finished.
2
Press PRO LOGIC or 3 STEREO
c whichever you want to use.
The PRO LOGIC or 3 STEREO indicator
lights up on the display.
• When Dolby Surround is activated, the sound mode is
cancelled temporarily.
3
Select and play a sound source encoded with Dolby
Surround. (with the 
DOLBY SURROUND
 mark).
To cancel the Dolby Surround mode,
 press PRO LOGIC
or 3 STEREO (the same button you have pressed to activate Dolby
Surround in step 1 above) so that neither PRO LOGIC nor 3 STEREO
indicator remains lit on the display.
PRO LOGIC
3 STEREO
• Each time you press the button, the Dolby Surround modes
changes as follows:
R
A
PR
RA
PRO LOGIC
3 STEREO
* Manufactured under license from Dolby Laboratories
Licensing Corporation. DOLBY, the double-D symbol, and
“PRO LOGIC” are trademarks of Dolby Laboratories
Licensing Corporation.
SHIFT
(15 m Sec)
(20 m Sec)
(25 m Sec)
(30 m Sec)
EN18-20;MX-J777V/PM6
7/8/99, 9:13 AM
20