JVC RX-8030VBK ユーザーズマニュアル
27
English
Basic Procedure
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Ex. When setting One Touch Operation to “ON.”
1. Press SETTING.
The last selected item appears on the display.
2. Turn MULTI JOG until an item you want
appears on the display.
• In this example, select “ONE TOUCH OPE.” For available
items, see the list “Basic Setting Items” on page 26.
3. Push in MULTI JOG (PUSH SET).
The current setting for the selected item appears on the display.
4. Turn MULTI JOG until a setting you want
appears on the display.
5. Press EXIT.
6. Repeat steps 2 to 5 to set other items if necessary.
7. Press EXIT.
The source indication resumes on the display.
Setting the Speakers
To obtain the best possible surround effect from the Surround and
DSP modes, register the setting about the speaker arrangement after
all connections are completed.
• If you have used Quick Speaker Setup on page 25, this setting is
DSP modes, register the setting about the speaker arrangement after
all connections are completed.
• If you have used Quick Speaker Setup on page 25, this setting is
not required.
7 Subwoofer setting—SUB WOOFER
Select whether you have connected a subwoofer or not.
YES: Select when a subwoofer is connected.
NO:
Select when no subwoofer is used.
Note:
If you have selected “NO” for the subwoofer, you cannot use the
SUBWOOFER OUT ON/OFF button on the front panel.
SUBWOOFER OUT ON/OFF button on the front panel.
7 Speaker size—FRONT SPEAKER, CNTR SPEAKER,
SURR SPEAKER, SBACK SPEAKER
Select the size for each connected speaker.
LARGE*
1
:
Select when the speaker size is relatively large.
SMALL*
2
:
Select when the speaker size is relatively small.
NONE:
Select this when you have not connected a
speaker. (Not selectable for the front speakers)
speaker. (Not selectable for the front speakers)
*
1
Initial setting for front speakers.
*
2
Initial setting for center, surround, and surround back
speakers.
speakers.
Notes:
• Keep the following comments in mind as reference when
adjusting.
– If the size of the cone speaker unit built in your speaker is
– If the size of the cone speaker unit built in your speaker is
larger than 12 cm (4
3
/
4
inches), select “LARGE,” and if it is
smaller than 12 cm (4
3
/
4
inches), select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can
only select “LARGE” for the front speakers.
• If you have selected “SMALL” for the front speakers, you cannot
select “LARGE” for the center, surround, and surround back
speakers.
speakers.
• If you have selected “SMALL” for the surround speakers, you
cannot select “LARGE” for the surround back speakers.
• If you have selected “NONE” for the surround speakers, the
surround back speakers are fixed to “NONE.”
7 Surround back speakers quantity—SBACK OUT
Select the number of the surround back speakers connected.
1SPK: Select this to use 1 surround back speaker.
2SPK: Select this to use 2 surround back speakers.
Note:
If you have selected “NONE” for the surround back speakers (see
above), this setting is not available.
above), this setting is not available.
: shows the initial setting in the following
tables.
VOLUME
LINEAR PCM
L
R
ANALOG
SPEAKERS 1
VOLUME
LINEAR PCM
L
R
ANALOG
SPEAKERS 1
VOLUME
LINEAR PCM
L
R
ANALOG
SPEAKERS 1
VOLUME
ONE TOUCH OPERATION
LINEAR PCM
L
R
ANALOG
SPEAKERS 1
25-30_8030&7030[C]7.pm6
03.2.13, 2:52 PM
27