Philips FW-D596 ユーザーズマニュアル
19
English
Preparations
IMPORTANT!
– Make sure to complete the
preparation procedures before operating
the system.
– Make sure to complete the
preparation procedures before operating
the system.
Step 1: Inserting batteries into
the remote control
the remote control
3
2
1
1
Open the battery compartment.
2
Place two batteries (Type R06 or AA) in the
compartment with the correct polarity as
indicated by “+” and “–” symbols.
compartment with the correct polarity as
indicated by “+” and “–” symbols.
3
Close the cover.
Using the remote control to operate the
system
system
1
Point the remote control directly
at the remote sensor (iR) on the
front panel.
at the remote sensor (iR) on the
front panel.
2
Select the source you wish to
control by pressing one of the
source select buttons on the
remote control (for example
TAPE, TUNER).
control by pressing one of the
source select buttons on the
remote control (for example
TAPE, TUNER).
3
Then select the desired function (for example
2;
,
4, ¢).
CAUTION!
– Remove batteries if they are
exhausted or will not be used for a long
time.
– Do not use old and new or different
types of batteries in combination.
– Batteries contain chemical substances,
so they should be disposed of properly.
– Remove batteries if they are
exhausted or will not be used for a long
time.
– Do not use old and new or different
types of batteries in combination.
– Batteries contain chemical substances,
so they should be disposed of properly.
Step 2: Setting the clock
The clock can be set in either 12-hour or 24-
hour mode (“
hour mode (“
PM 00:00” or “00:00” for
example).
1
Go into Standby mode.
➜ If you have not set the clock, “--:--” will blink
until you set the clock.
➜ If you have not set the clock, “--:--” will blink
until you set the clock.
2
Press CLOCK and “
00:00” blinks on the
display.
➜ The current time is flashing on the display.
➜ The current time is flashing on the display.
➜ If you have not set the clock, “--:--” will appear
on the display.
on the display.
3
Press O or P on the system to set the hours.
4
Press 5 or 6 on the system to set the minutes.
5
Press CLOCK to confirm your setting, and then
go into standby mode. The system will store the
setting automatically.
➜ The time setting becomes effective.
go into standby mode. The system will store the
setting automatically.
➜ The time setting becomes effective.
To exit the setting without storing
● Press 9 on the system to exit.
➜ “CANCEL” will appear on the display.
● Press ECO POWER to exit setting mode and
go into ECO POWER mode.
● You can also press DISC, DISC1~3, DISC
CHANGE, OPEN/CLOSE to exit setting
mode and go into disc mode.
mode and go into disc mode.
● The system will also exit setting mode and go to
tuner, AUX, tape mode wheh you press the
corresponding source button.
corresponding source button.
Viewing the clock
● In Standby mode, Press DISPLAY on the
system to toggle between 12-hour and 24-hour
modes.
➜ The time will be displayed.
modes.
➜ The time will be displayed.
Notes:
– The clock will be cancelled when the power cord
is disconnected or if a power failure occurs.
– During clock setting, if no button is pressed
within 30 seconds, the system will exit the setting
mode and go into standby mode.
– The clock will be cancelled when the power cord
is disconnected or if a power failure occurs.
– During clock setting, if no button is pressed
within 30 seconds, the system will exit the setting
mode and go into standby mode.
TAPE 1/2