ONKYO CR-N755 ユーザーズマニュアル
35
Custom Setup
The common setting for each input selector is explained
below. Go through the following steps for setup.
below. Go through the following steps for setup.
Tip:
• You can also use the [MENU/ENTER] jog dial on the
• You can also use the [MENU/ENTER] jog dial on the
CD receiver.
Preferences
ASb (Auto Standby)
When “Auto Standby” is set to “On”, the CD receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio signal input.
The ASb indicator lights up when the Auto Standby
function is enabled.
When “Auto Standby” is set to “On”, the CD receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio signal input.
The ASb indicator lights up when the Auto Standby
function is enabled.
Default setting: On (European models), Off (Other
models)
models)
Update
These settings allow you to update the CD receiver’s
firmware. Do not shutdown the power of the CD receiver
while updating.
These settings allow you to update the CD receiver’s
firmware. Do not shutdown the power of the CD receiver
while updating.
SleepCharge
You can specify how the power is fed to your USB
device (mobile device) when the CD receiver is in
standby mode.
You can specify how the power is fed to your USB
device (mobile device) when the CD receiver is in
standby mode.
Note:
• When the “SleepCharge” setting is set to “On”, the
• When the “SleepCharge” setting is set to “On”, the
power consumption slightly increases in standby
mode.
mode.
• If the iPod/iPhone completely runs out of battery,
charging might not work. In that case you need to turn
the power on again.
the power on again.
• If you disconnect the USB device while
“ReadyCharging” appears, the CD receiver does not
enter the standby mode. Press the On/Standby [
enter the standby mode. Press the On/Standby [
8]
button to enter the standby mode again.
• Only the USB port (front) can be used for charging.
Sel Change
When you connect an Onkyo
When you connect an Onkyo
u-capable component,
it’s important that you select the input source name that
matches the type of component for
matches the type of component for
u to work properly.
Before operating this setting, you need to select the input
source that you want to set.
source that you want to set.
LINE1, LINE2, OPTICAL, COAXIAL
DOCK
Note:
• “DOCK” can be selected for the “LINE1”, “LINE2”,
• “DOCK” can be selected for the “LINE1”, “LINE2”,
“OPTICAL”, “COAXIAL” input selector, but not at
the same time.
the same time.
M.OPT (Music Optimizer)
The Music Optimizer function enhances the sound
quality of compressed music files. When set to “On”, the
M.OPT indicator lights on the CD receiver’s display.
The Music Optimizer function enhances the sound
quality of compressed music files. When set to “On”, the
M.OPT indicator lights on the CD receiver’s display.
Note:
• This setting can be used only for the NET and USB
• This setting can be used only for the NET and USB
input selectors.
• The Music Optimizer function only works with digital
audio input signals with a sampling rate below
48 kHz.
48 kHz.
Setting Common Preferences
1
Press the [MENU] button, and then use the
Arrow [
Arrow [
!]/["] buttons to select the
preference you want to change.
2
Press [ENTER].
3
Use the Arrow [
#]/[$] buttons to select the
preference’s options.
4
Press [ENTER].
On
Off
Off
Version
Displays the current version of the firmware.
Displays the current version of the firmware.
Update Notice
Enable (default)
Disable
Disable
When this setting is enabled, you will be notified if a
firmware update via network is available.
firmware update via network is available.
CR via NET: Performs the firmware update via
Internet. Check the network
connection before updating.
connection before updating.
CR via USB:
Performs the firmware update from a
USB flash drive.
USB flash drive.
On:
(default)
(default)
If you connect USB device (mobile
device), charging will start.
“Charging” appears on the display.
device), charging will start.
“Charging” appears on the display.
Off:
Your USB device (mobile device)
is not charged.
is not charged.
On
Off (default)
Off (default)
→
→