Metra Electronics 99-7500 ユーザーズマニュアル
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed.
Remove the pocket and (2) screws exposed.
Remove the radio trim bezel and disconnect
the wiring. Remove (4) screws securing the
factory dummy plate to the back of the bezel
and discard the plate.
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed.
Remove the pocket and (2) screws exposed.
Remove the radio trim bezel and disconnect
the wiring. Remove (4) screws securing the
factory dummy plate to the back of the bezel
and discard the plate.
1
MAZDA 626 / MX6 1986-92
(models equipped with factory receiver/pocket)
2
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "E". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
Housing #2 EXCEPT tabs "E". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
5
2
"E"
"E"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed in the
ashtray cavity. Unsnap the gear shifter trim
and remove (2) screws exposed. Unsnap
the climate control trim bezel and remove (2)
screws exposed. Remove the dash trim
bezel and disconnect the wiring. Remove
(4) screws securing the factory head unit
and disconnect the wiring.
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed in the
ashtray cavity. Unsnap the gear shifter trim
and remove (2) screws exposed. Unsnap
the climate control trim bezel and remove (2)
screws exposed. Remove the dash trim
bezel and disconnect the wiring. Remove
(4) screws securing the factory head unit
and disconnect the wiring.
1
MAZDA RX-7 1986-91
2
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "A". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
Housing #1 EXCEPT tabs "A". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
"A"
"A"
"A"
"A"
"A"
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed.
Remove the pocket and (2) screws exposed.
Remove the radio trim bezel and disconnect
the wiring. Remove (4) screws securing the
factory dummy plate to the back of the bezel
and discard the plate.
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed.
Remove the pocket and (2) screws exposed.
Remove the radio trim bezel and disconnect
the wiring. Remove (4) screws securing the
factory dummy plate to the back of the bezel
and discard the plate.
1
MAZDA 626 / MX6 1986-92
(models equipped with factory receiver/tape deck/eq/pocket)
2
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "B". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
Housing #1 EXCEPT tabs "B". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
"B"
"B"
"B"
"B"
"B"
"B"
"B"
"B"
2-SHAFT HEAD UNITS: For models using Radio Housing #1, attach the Faceplate to the
Housing. Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A).
For models using Radio Housing #2, slide the aftermarket head unit into the kit and secure
with shaft nuts. (see Fig. B)
Housing. Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A).
For models using Radio Housing #2, slide the aftermarket head unit into the kit and secure
with shaft nuts. (see Fig. B)
ALL VEHICLES
3a
Fig. B
Fig. A