ONKYO TX-SR702 操作ガイド
47
First Time Setup
—Continued
Crossover
Notes:
• If the crossover frequency is set to a low value, and the
program material doesn’t contain any sounds below
that frequency, the subwoofer will not output much
sound.
that frequency, the subwoofer will not output much
sound.
6
Use the Up and Down [
]/[
]
buttons to select “c. Center,” and
then use the Left and Right [
then use the Left and Right [
]/
[
] buttons to select:
Small:
Select if the center speaker is
small.
small.
Large:
Select if the center speaker is
large.
large.
None:
Select if no center speaker is
connected.
connected.
Note:
• If the Front setting in step 5 is set to
Small, the Large option cannot be
selected.
selected.
7
Use the Up and Down [
]/[
]
buttons to select “d. Surround,”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select:
Small:
Select if the surround left and
right speakers are small.
right speakers are small.
Large:
Select if the surround left and
right speakers are large.
right speakers are large.
None:
Select if no surround left and
right speakers are connected.
right speakers are connected.
Note:
• If the Front setting in step 5 is set to
Small, the Large option cannot be
selected.
selected.
8
Use the Up and Down [
]/[
]
buttons to select “e. Surround
Back,” and then use the Left and
Right [
Back,” and then use the Left and
Right [
]/[
] buttons to select:
Small:
Select if the surround back
left and right speakers are
small.
small.
Large:
Select if the surround back
speakers are large.
None:
Select if no surround back
speakers are connected.
Notes:
• If the Surround setting in step 7 is set
to None, this setting cannot be
selected.
selected.
• If the Surround setting in step 7 is set
to Small, this setting cannot be set to
Large.
Large.
ENTER
ENTER
ENTER
9
Use the Up and Down [
]/[
]
buttons to select “f. SurrBack
ch,” and then use the Left and
Right [
ch,” and then use the Left and
Right [
]/[
] buttons to select:
1ch:
Select if one surround back
speaker is connected.
2ch:
Select if two (left and right)
surround back speakers are
connected.
connected.
Continue with step 10 in the right col-
umn.
umn.
10
Use the Up and Down [
]/[
]
buttons to select “g. Crossover,”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select a
crossover frequency.
Choose a crossover frequency suitable
for your setup. If you’re using a sub-
woofer, choose a crossover frequency
based on the diameter of your front
speakers. If you’re not using a sub-
woofer, use the diameter of any speaker
that you specified as Small.
for your setup. If you’re using a sub-
woofer, choose a crossover frequency
based on the diameter of your front
speakers. If you’re not using a sub-
woofer, use the diameter of any speaker
that you specified as Small.
For the TX-SR702/702E, if you’re
using THX-certified speakers, select
80Hz (THX).
using THX-certified speakers, select
80Hz (THX).
*TX-SR702/702E only.
Continue with step 11 on the next page.
ENTER
ENTER
Speaker cone
diameter
Crossover
frequency
Over 12 in.
(30 cm)
40Hz*
8 to 12 in.
(20–30 cm)
60Hz
6-1/2 to 8 in.
(16–20 cm)
80Hz (THX)
5-1/4 to 6-1/2 in.
(13–16 cm)
100Hz
3-1/2 to 5-1/4 in.
(9–13 cm)
120Hz
Under 3-1/2 in.
(9 cm)
150Hz
TX-NR702,602_En.book Page 47 Tuesday, September 7, 2004 1:18 PM