JVC WB-1540 ユーザーズマニュアル
6
Installation and Connection (WB-1540)
1.
Dismantle the gasket and gasket gland
Loosen the 6 Screws B (M4) using a driver, followed by
dismantling the gasket and gasket gland from the lower
housing.
T The 6 Screws B (M4) cannot be totally removed from
dismantling the gasket and gasket gland from the lower
housing.
T The 6 Screws B (M4) cannot be totally removed from
the gasket to prevent it from falling off.
2.
Dismantle the lower housing
Loosen the 3 Screws A (M4 x 6) using a driver, followed
by dismantling the lower housing from the main housing
unit.
T The lower housing is connected to the main housing
by dismantling the lower housing from the main housing
unit.
T The lower housing is connected to the main housing
unit using a safety wire.
1.
Connect the AC 24 V output cable to the camera
Connect the AC 24 V output cable of the main board to
the camera’s ceiling mount bracket.
the camera’s ceiling mount bracket.
2.
Connect other cables
Connect the necessary cables supplied with the housing
(coaxial video cable, communication cable, etc.) to the
ceiling mount.
(coaxial video cable, communication cable, etc.) to the
ceiling mount.
3.
Mount the camera’s ceiling mount to the main
housing unit.
housing unit.
Use the 4 screws supplied (M4 x 20) to mount the ceiling
mount to the main housing unit.
mount to the main housing unit.
4.
Mount the camera to the ceiling mount
Follow instructions in the manual of the camera in use to
mount the camera to the ceiling mount.
mount the camera to the ceiling mount.
Disassembling the Housing
2.
1.
Main Housing Unit
Screw A (M4 x 6) x 3
Lower Housing
Gasket
Gasket Gland
Screw B (M4) x 6
Safety Wire
CAUTION:
Pay careful attention to store the dismantled parts and
screws until assembly is complete to prevent them from
being misplaced.
Pay careful attention to store the dismantled parts and
screws until assembly is complete to prevent them from
being misplaced.
Mounting the Camera (TK-C625)
3.
1.
2.
4.
Interior of Housing
Notch
Camera Mounting Bracket
Safety Wire
Main Board
AC 24 V
Output Cable
Output Cable
To [POWER INPUT AC 24 V]
Terminal of Ceiling Mount
Terminal of Ceiling Mount
Cables
Cover
FRONT
Mark
Mark
Ceiling Mount
Screws Supplied
(M4 x 20) x 4
(M4 x 20) x 4
Camera
JVC Mark
Before mounting.
Remove the ceiling mount cover of the camera and guide the
cables supplied with WB-1540 through the cover.
T For further details, please refer to the instruction manual of
Remove the ceiling mount cover of the camera and guide the
cables supplied with WB-1540 through the cover.
T For further details, please refer to the instruction manual of
the camera in use.
CAUTION:
● Connect the communication cable to the [ALARM IN/OUT]
● Connect the communication cable to the [ALARM IN/OUT]
and [CONTROL] terminals if necessary. For safety
reasons, ensure to cut off any excess cable and bind using
an insulating tape before use.
reasons, ensure to cut off any excess cable and bind using
an insulating tape before use.
● For further details on connection, please refer to the
instruction manual of the camera in use.
● Ensure to bind connectors of LAN cables and DC 12 V
Power Cable that are not in use with an insulating tape
before use.
before use.
NOTE:
During mounting, align the [D FRONT] Mark of the ceiling
mount with the notch on the camera mount bracket of the
main housing unit.
During mounting, align the [D FRONT] Mark of the ceiling
mount with the notch on the camera mount bracket of the
main housing unit.
TK-C625