JVC DT-3D24G1 ユーザーズマニュアル

26

This monitor has three external control terminals.

●

 MAKE/TRIGGER terminal (RJ-45): The following external control 

systems are available.
1  MAKE (make contact) system:

Controls the monitor by short-circuiting the corresponding pin 
terminal to the GND pin terminal, or disconnecting (opening) it.

2  TRIGGER (trigger) system:

Controls the monitor by sending the pulse signal 
instantaneously to the corresponding pin terminal.

→ “Using the MAKE/TRIGGER system” on the right.

●

 RS-485 terminal (RJ-45): Controls the monitor with the RS-485 

system (→ “Using the serial communication” on page 28).

●

 RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-

232C system (→ “Using the serial communication” on page 28).

Set the following items of “REMOTE SETTING” in SET-UP MENU 
according to the external control terminal and control system (→ 
“SERIAL TYPE,” “PARALLEL TYPE” on page 24).

—

MAKE

—

TRIGGER

RS485 

*1

—

RS232C 

*1

—

*1

  For a monitor connected to a personal computer etc, select 

the terminal the equipment is actually connected to. For other 
monitors, select “RS485.”

Control priority is as follows.
MAKE > TRIGGER = serial communication = buttons and menu on 
the monitor

●

 You can use external control even when “CONTROL LOCK” is set to 

“VOL.LOCK” or “ALL LOCK.” (→ page 25)

●

 When the monitor is off (on standby), external control is not 

available. But certain external controls (starting/terminating 
communication, turning on the monitor) are available through the 
serial communication. (→ page 29)

<MAKE/TRIGGER system>
You can control the monitor by a personal computer or dedicated 
controller

*2

.

●

 “Using the MAKE/TRIGGER system” on the right.

*2

  The controller is not commercially available. Consult your dealer if 

you need it.

PC, etc.

RS-485 
IN

RS-485 IN
or
RS-232C

RS-485 
OUT

RS-485 
IN

RS-485 
OUT

RS-485 
OUT

●

 For the details, see page 28.

The MAKE/TRIGGER terminal is configured as follows.
You can assign a function to each pin terminal in “REMOTE SETTING.”
(→ “PIN1, PIN2, PIN3, PIN4, PIN5” in “PARALLEL TYPE” on page 24)

●

 You cannot change the functions assigned to the pin terminals 

from 6th to 8th.

This is a female 
terminal.

PIN1

PIN2

PIN3

PIN4

PIN5

TALLY 

*1

ENABLE 

*2

GND

*1

  The 6th pin terminal controls turning on or off the tally lamp 

(available to control even when the 7th pin terminal is invalid).

*2

  The 7th pin terminal makes the external control valid/invalid. 

Make sure to control the terminal by the MAKE system.

For the operation procedure, see page 18.

1  Select “REMOTE SETTING” on the SET-UP MENU.
2  Set “PARALLEL TYPE” to “SET.”
3  Select a pin name (“PIN1” – “PIN5”) for which you want 

to assign a function, then select the function you want 
to assign.

For the selectable functions, see the table on page 29.

1  Set “PARALLEL TYPE” of “REMOTE SETTING” to “MAKE” 

or “TRIGGER” in the SET-UP MENU.

2  Short-circuit the 7th pin terminal (ENABLE) to the 

8th pin terminal (GND) so that the monitor can be 
controlled by the external control.

3  When the “MAKE” system is selected:
 

Operate each function by short-circuiting the 
corresponding pin terminal to the 8th pin terminal 
(GND) or opening it.

 

 

Operate each function by pulse control, that is short-
circuiting the corresponding pin terminal to the 8th pin 
terminal (GND) for about 1 second and opening it.

●

 When changing the input with MAKE system, only one pin terminal 

must be short-circuited. (Other pin terminals must be opened.)

●

 When selecting the “TRIGGER” system, you can operate only one 

function at a time. Operate the functions one by one.

DT3D24G1_EN.indb   26

DT3D24G1_EN.indb   26

11.1.25   0:53:55 PM

11.1.25   0:53:55 PM